Effect of SiO₂ and Al₂O₃ Hybrid Nano Materials on Fatigue Behavior for Laminated Composite Materials Used to Manufacture Artificial Socket Prostheses

Abstract:

Most artificial socket prostheses are applied to fatigue load; therefore, more failure of socket prostheses occur due to fatigue loading. Then, it was necessary to improve the fatigue characterizations of composite materials used to manufacture the artificial socket prostheses by using hybrid nanomaterials, with different types and amounts. So, this work suggested mixing two nanomaterials types to improve the mechanical and fatigue properties of composite materials. Therefore, the experimental work used to manufacture tensile and fatigue samples of composite with different nanoweight fraction effects, in addition to calculating the mechanical properties and fatigue behavior for its composite. There, strength and modulus of elasticity, in addition to, fatigue strength and life evaluating of composite with different nanomaterials mixing. Also, the numerical technique by using the finite element method is used to calculate fatigue life and strength of composite materials. Also, comparison fatigue results were calculated by experimental work with fatigue results evaluated by numerical technique to give the discrepancy for results evaluation. Hence, the comparison of results showed good agreement for the technique used to evaluate the fatigue behavior of composite materials with the nanoeffect, where, the maximum error did not exceed (11.86%). Finally, the results have shown that the reinforcement by mixing two Nanomaterial types lead to improvement in the mechanical properties and fatigue behavior to more than (35%) and increasing the mechanical properties and fatigue behavior to (10%) more than the increase of properties and fatigue characterizations reinforcement by one Nanomaterial type.

• Periodical: Materials Science Forum (Volume 1039)
• Pages: 493-509
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.1039.493
• Online since: July 2021
• Authors: Nesreen Dakhel, Ameer A. Kadhim, Rasha Hayder Al-Khayat*, Muhannad Al-Waily
• Keywords: Artificial Prostheses Fatigue, Fatigue Composite, Hybrid Nano, Nano, Nanofatigue

References

[1] Ameer A Kadhim, Muhannad Al-Waily, Zaman Abud Almalik Abud Ali, Muhsin J Jweeg and Kadhim K Resan, Improvement Fatigue Life and Strength of Isotropic Hyper Composite Materials by Reinforcement with Different Powder Materials, International Journal of Mechanical & Mechatronics Engineering, 18, 2 (2018).

[2] Kadhim K Resan, Abbas A Alasadi, Muhannad Al-Waily and Muhsin J Jweeg, Influence of Temperature on Fatigue Life for Friction Stir Welding of Aluminum Alloy Materials, International Journal of Mechanical & Mechatronics Engineering, 18, 2 (2018).

[3] Worood Hussein and Mohsin Abdullah Al-Shammari, Fatigue and Fracture Behaviours of FSW and FSP Joints of AA5083-H111 Aluminium Alloy, IOP Conference Series: Materials Science and Engineering, International Conference on Materials Engineering and Science, 454 (2018).

DOI: 10.1088/1757-899x/454/1/012055

[4] Saif M Abbas, Kadhim K Resan, Ahmed K Muhammad and Muhannad Al-Waily, Mechanical and Fatigue Behaviors of Prosthetic for Partial Foot Amputation with Various Composite Materials Types Effect, International Journal of Mechanical Engineering and Technology, 9, 9 (2018) 383–394.

[5] Mohsin Abdullah Al-Shammari, Qasim H Bader, Muhannad Al-Waily and A M Hasson, Fatigue Behavior of Steel Beam Coated with Nanoparticles under High Temperature, Journal of Mechanical Engineering Research and Developments, 43, 4 (2020) 287–298.

[6] Muhannad Al-Waily and Zaman Abud Almalik Abud Ali, A Suggested Analytical Solution of Powder Reinforcement Effect on Buckling Load for Isotropic Mat and Short Hyper Composite Materials Plate, International Journal of Mechanical & Mechatronics Engineering, 15, 4 (2015).

[7] Jumaa S Chiad, Muhannad Al-Waily and Mohsin Abdullah Al-Shammari, Buckling Investigation of Isotropic Composite Plate Reinforced by Different Types of Powders, International Journal of Mechanical Engineering and Technology, 9, 9 (2018) 305–317.

[8] Jawad K Oleiwi, Qahtan Adnan Hamad and Hadil Jabbar Abdul Rahman, Tensile Properties and Morphological Test of Heat Cured Acrylic Resin Reinforced by Natural Powders, International Journal of Mechanical and Production Engineering Research and Development, 8, 6 (2018).

DOI: 10.24247/ijmperddec201837

[9] Mohsin Abdullah Al-Shammari and Sahar Emad Abdullah, Stiffness to Weight Ratio of Various Mechanical and Thermal Loaded Hyper Composite Plate Structures, IOP Conference Series: Materials Science and Engineering, 2nd International Conference on Engineering Sciences, 433 (2018).

DOI: 10.1088/1757-899x/433/1/012051

[10] Sihama Issa Salih, Jawad Kadhim Oleiwi and Arkan Saad Mohamed, Investigation of Mechanical Properties of Pmma Composite Reinforced with Different Types of Natural Powders, ARPN Journal of Engineering and Applied Sciences, 13, 22 (2018).

[11] Jawad K Oleiwi, Qahtan Adnan Hamad and Hadil Jabbar Abdul Rahman, Experimental Investigation of Flexural and Impact Properties of PMMA Reinforced by Bamboo and Rice Husk Powders, International Journal of Mechanical Engineering and Technology, 9, 10 (2018).

[12] Nada N Kadhim, Qahtan A Hamad and Jawad K Oleiwi, Tensile and Morphological Properties of PMMA Composite Reinforced by Pistachio Shell Powder used in Denture Applications, 2nd International Conference on Materials Engineering & Science, AIP Conference Proceedings (2020).

DOI: 10.1063/5.0000181

[13] Ehab N Abbas, Muhsin J Jweeg and Muhannad Al-Waily, Analytical and Numerical Investigations for Dynamic Response of Composite Plates Under Various Dynamic Loading with the Influence of Carbon Multi-Wall Tube Nano Materials, International Journal of Mechanical & Mechatronics Engineering, 18, 6 (2018).

[14] Marwah Mohammed Abdulridha, Nasreen Dakel Fahad and Muhannad Al-Waily, Kadhim K Resan, Rubber Creep Behavior Investigation with Multi Wall Tube Carbon Nano Particle Material Effect, International Journal of Mechanical Engineering and Technology, 9, 12 (2018) 729–746.

[15] Noor Dhia Yaseen, Jumaa S Chiad and Firas Mohammed Abdul Ghani, The Study and Analysis of Stress Distribution Subjected on the Replacement Knee Joint Components using Photo-Elasticity and Numerical Methods, International Journal of Mechanical and Production Engineering Research and Development, 8, 6 (2018).

DOI: 10.24247/ijmperddec201849

[16] Muhannad Al-Waily, Mohsin Abdullah Al-Shammari and Muhsin J. Jweeg, An Analytical Investigation of Thermal Buckling Behavior of Composite Plates Reinforced by Carbon Nano Particles, Engineering Journal, 24, 3 (2020).

DOI: 10.4186/ej.2020.24.3.11

[17] Muhannad Al-Waily, Iman Q. Al Saffar, Suhair G. Hussein and Mohsin Abdullah Al-Shammari, Life Enhancement of Partial Removable Denture made by Biomaterials Reinforced by Graphene Nanoplates and Hydroxyapatite with the Aid of Artificial Neural Network, Journal of Mechanical Engineering Research and Developments, 43, 6 (2020) 269-285.

[18] Fahad M Kadhim, Jumaa S Chiad and Maryam Abdul Salam Enad, Evaluation and Analysis of Different Types of Prosthetic Knee Joint Used by above Knee Amputee, Defect and Diffusion Forum Journal, 398 (2020) 34-40.

DOI: 10.4028/www.scientific.net/ddf.398.34

[19] Bashar A Bedaiwi and Jumaa S Chiad, Vibration Analysis and Measurement in the Below Knee Prosthetic Limb Part I: Experimental Work, ASME 2012 International Mechanical Engineering Congress and Exposition, Proceedings (2012).

DOI: 10.1115/imece2012-85811

[20] Mohsin Abdullah Al-Shammari, Emad Q Hussein and Ameer Alaa Oleiwi, Material Characterization and Stress Analysis of a Through Knee Prosthesis Sockets, International Journal of Mechanical & Mechatronics Engineering, 17, 6 (2017).

[21] Saif M Abbas, Ayad M Takhakh, Mohsin Abdullah Al-Shammari and Muhannad Al-Waily, Manufacturing and Analysis of Ankle Disarticulation Prosthetic Socket (SYMES), International Journal of Mechanical Engineering and Technology, 9, 7 (2018) 560–569.

[22] Muhsin J Jweeg, Zaid S Hammoudi and Bassam A Alwan, Optimised Analysis, Design, and Fabrication of Trans-Tibial Prosthetic Sockets, IOP Conference Series: Materials Science and Engineering, 2nd International Conference on Engineering Sciences, 433 (2018).

DOI: 10.1088/1757-899x/433/1/012058

[23] Ahmed Khaleel Abdulameer and Mohsin Abdullah Al-Shammari, Fatigue Analysis of Syme's Prosthesis, International Review of Mechanical Engineering, 12, 3 (2018).

[24] Ayad M Takhakh, Saif M Abbas and Aseel.K Ahmed, A Study of the Mechanical Properties and Gait Cycle Parameter for a Below-Knee Prosthetic Socket, IOP Conference Series: Materials Science and Engineering, 2nd International Conference on Engineering Sciences, 433 (2018).

DOI: 10.1088/1757-899x/433/1/012045

[25] Fahad M Kadhim, Ayad M Takhakh and Asmaa M Abdullah, Mechanical Properties of Polymer with Different Reinforcement Material Composite That used for Fabricates Prosthetic Socket, Journal of Mechanical Engineering Research and Developments, 42, 4 (2019) 118–123.

DOI: 10.26480/jmerd.04.2019.118.123

[26] Muhsin J Jweeg, Abdulkareem Abdulrazzaq Ahumdany and Ali Faik Mohammed Jawad, Dynamic Stresses and Deformations Investigation of the Below Knee Prosthesis using CT-Scan Modeling, International Journal of Mechanical & Mechatronics Engineering, 19, 1 (2019).

[27] Ehab N. Abbas, Muhsin J. Jweeg and Muhannad Al-Waily, Fatigue Characterization of Laminated Composites used in Prosthetic Sockets Manufacturing, Journal of Mechanical Engineering Research and Developments, 43, 5 (2020) 384-399.

[28] Muhannad Al-Waily, Moneer H Tolephih and Muhsin J Jweeg, Fatigue Characterization for Composite Materials used in Artificial Socket Prostheses with the Adding of Nanoparticles, IOP Conference Series: Materials Science and Engineering, 2nd International Scientific Conference of Al-Ayen University, 928 (2020).

DOI: 10.1088/1757-899x/928/2/022107

[29] Ayad M Takhakh, Fahad M Kadhim and Jumaa S Chiad, Vibration Analysis and Measurement in KNEE Ankle Foot Orthosis for Both Metal and Plastic KAFO Type, ASME International Mechanical Engineering Congress and Exposition, Proceedings (2013).

DOI: 10.1115/imece2013-64641

[30] S H Bakhy, S S Hassan, S M Nacy, K Dermitzakis and A H Arieta, Contact Mechanics for Soft Robotic Fingers: Modeling and Experimentation, Robotica (2013).

DOI: 10.1017/s0263574712000653

[31] Jumaa S Chiad, Study the Impact Behavior of the Prosthetic Lower Limb Lamination Materials due to Low Velocity Impactor, ASME 2014 12th Biennial Conference on Engineering Systems Design and Analysis (2014).

DOI: 10.1115/esda2014-20007

[32] S H Bakhy, Modeling of Contact Pressure Distribution and Friction Limit Surfaces for Soft Fingers in Robotic Grasping, Robotica (2014).

DOI: 10.1017/s0263574713001215

[33] Mahmud Rasheed Ismail, Muhannad Al-Waily and Ameer A Kadhim, Biomechanical Analysis and Gait Assessment for Normal and Braced Legs, International Journal of Mechanical & Mechatronics Engineering, 18, 3 (2018).

[34] Sadeq Bakhy, Enass Flaieh and Mortada Jabbar, An Experimental Study for Grasping and Pinching Controls for an Underactuated Robotic Finger Using a PID Controller, IOP Conference Series: Materials Science and Engineering, 2nd International Conference on Engineering Sciences, 433 (2018).

DOI: 10.1088/1757-899x/433/1/012047

[35] Yusra Alyas Shafeeq, Jumaa S Chiad and Yassr Y Kahtan, Study, Analysis, the Vibration and Stability for the Artificial Hand During Its Daily Working, International Journal of Mechanical Engineering and Technology, 9, 13 (2018) 1706–1716.

[36] Lara E Yousif, Kadhim K Resan and Raad M Fenjan, Temperature Effect on Mechanical Characteristics of A New Design Prosthetic Foot, International Journal of Mechanical Engineering and Technology, 9, 13 (2018) 1431–1447.

[37] Fahad M Kadhim, Jumaa S Chiad and Ayad M Takhakh, Design And Manufacturing Knee Joint for Smart Transfemoral Prosthetic, IOP Conference Series: Materials Science and Engineering, International Conference on Materials Engineering and Science, 454 (2018).

DOI: 10.1088/1757-899x/454/1/012078

[38] Ayad M Takhakh and Saif M Abbas, Manufacturing and Analysis of Carbon Fiber Knee Ankle Foot Orthosis, International Journal of Engineering & Technology, 7, 4 (2018) 2236–2240.

DOI: 10.14419/ijet.v7i4.17315

[39] Muhsin J Jweeg, Muhannad Al-Waily, Ahmed K Muhammad and Kadhim K Resan, Effects of Temperature on the Characterisation of a New Design for a Non-Articulated Prosthetic Foot, IOP Conference Series: Materials Science and Engineering, 2nd International Conference on Engineering Sciences, 433 (2018).

DOI: 10.1088/1757-899x/433/1/012064

[40] Muhannad Al-Waily, Emad Q Hussein and Nibras A Aziz Al-Roubaiee, Numerical Modeling for Mechanical Characteristics Study of Different Materials Artificial Hip Joint with Inclination and Gait Cycle Angle Effect, Journal of Mechanical Engineering Research & Developments, 42, 4 (2019) 79–93.

DOI: 10.26480/jmerd.04.2019.79.93

[41] Mortada A Jabbar, Sadeq H Bakhy and Enass H Flaieh, A New Multi-Objective Algorithm for Underactuated Robotic Finger During Grasping and Pinching Assignments, 3rd International Conference on Engineering Sciences, IOP Conference Series: Materials Science and Engineering, 671 (2020).

DOI: 10.1088/1757-899x/671/1/012135

[42] Fahad M Kadhim, Ayad M Takhakh and Jumaa S Chiad, Modeling and Evaluation of Smart Economic Transfemral Prosthetic, Defect and Diffusion Forum Journal, 398 (2020) 48-53.

DOI: 10.4028/www.scientific.net/ddf.398.48

[43] Esraa A. Abbod, Muhannad Al-Waily, Ziadoon M. R. Al-Hadrayi, Kadhim K. Resan and Saif M. Abbas, Numerical and Experimental Analysis to Predict Life of Removable Partial Denture, IOP Conference Series: Materials Science and Engineering, 1st International Conference on Engineering and Advanced Technology, 870 (2020).

DOI: 10.1088/1757-899x/870/1/012149

[44] Muhannad Al-Waily, Alaa Abdulzahra Deli, Aziz Darweesh Al-Mawash and Zaman Abud Almalik Abud Ali, Effect of Natural Sisal Fiber Reinforcement on the Composite Plate Buckling Behavior, International Journal of Mechanical & Mechatronics Engineering, 17, 1 (2017).

[45] Mahmud Rasheed Ismail, Zaman Abud Almalik Abud Ali and Muhannad Al-Waily, Delamination Damage Effect on Buckling Behavior of Woven Reinforcement Composite Materials Plate, International Journal of Mechanical & Mechatronics Engineering, 18, 5 (2018) 83–93.

[46] Abeer R Abbas, Kadhim A Hebeatir and Kadhim K Resan, Effect of Laser Energy on the Structure of Ni46–Ti50–Cu4 Shape-Memory Alloy, International Journal of Nanoelectronics and Materials, 11, 4 (2018) 481–498.

DOI: 10.1088/1757-899x/1094/1/012135

[47] Yousuf Jamal Mahboba and Mohsin Abdullah Al-Shammari, Enhancing wear rate of high-density polyethylene (HDPE) by adding ceramic particles to propose an option for artificial hip joint liner, IOP Conference Series: Materials Science and Engineering 561 (2019).

DOI: 10.1088/1757-899x/561/1/012071

[48] Ekhlas Edan Kader, Akram Mahdi Abed and Mohsin Abdullah Al-Shammari, Al2O3 Reinforcement Effect on Structural Properties of Epoxy Polysulfide Copolymer, Journal of Mechanical Engineering Research and Developments, 43, 4 (2020) 320–328.

[49] Muhsin J Jweeg, Kadhim K Resan, Esraa A Abbod and Muhannad Al-Waily, Dissimilar Aluminium Alloys Welding by Friction Stir Processing and Reverse Rotation Friction Stir Processing, IOP Conference Series: Materials Science and Engineering, International Conference on Materials Engineering and Science, 454 (2018).

DOI: 10.1088/1757-899x/454/1/012059

[50] Abeer R Abbas, Kadhim A Hebeatir and Kadhim K Resan, Effect of CO2 Laser on Some Properties of NI46TI50CU4 Shape Memory Alloy, International Journal of Mechanical and Production Engineering Research and Development, 8, 2 (2018) 451–460.

DOI: 10.24247/ijmperdapr201852

[51] H J Abbas, M J Jweeg, Muhannad Al-Waily and Abbas Ali Diwan, Experimental Testing and Theoretical Prediction of Fiber Optical Cable for Fault Detection and Identification, Journal of Engineering and Applied Sciences, 14, 2 (2019) 430–438.

DOI: 10.36478/jeasci.2019.430.438

[52] Sadiq emad Sadiq, Sadeq Hussein Bakhy and Muhsin Jaber Jweeg, Effects of Spot Welding Parameters on the Shear Characteristics of Aluminum Honeycomb Core Sandwich Panels in Aircraft structure, Test Engineering and Management, 83 (2020) 7244 –7255.

DOI: 10.1088/1757-899x/928/2/022126

[53] Akeel Z Mahdi, Samir A Amin and Sadeq H Bakhy, Influence of Refill Friction Stir Spot Welding Technique on the Mechanical Properties and Microstructure of Aluminum AA5052 and AA6061-T3, IOP Conference Series: Materials Science and Engineering, 3rd International Conference on Engineering Sciences, vol 671 (2020).

DOI: 10.1088/1757-899x/671/1/012156

[54] ASTM D638-14, Standard Test Method for Tensile Properties of Plastics, ASTM International, West Conshohocken, United States (2015).

[55] Muhsin J Jweeg, Application of Finite Element Analysis to Rotating Fan Impellers, Doctoral Thesis, Aston University (1983).

[56] Muhsin J Jweeg, Ali S Hammood and Muhannad Al-Waily, A Suggested Analytical Solution of Isotropic Composite Plate with Crack Effect, International Journal of Mechanical & Mechatronics Engineering, 12, 5 (2012).

[57] Ragad Aziz Neama, Maher A R Sadiq Al-Baghdadi and Muhannad Al-Waily, Effect of Blank Holder Force and Punch Number on the Forming Behavior of Conventional Dies, International Journal of Mechanical & Mechatronics Engineering, 18, 4 (2018).

[58] Mohsin Abdullah Al-Shammari, Lutfi Y Zedan and Akram M Al-Shammari, FE Simulation of Multi-Stage Cold Forging Process For Metal Shell of Spark Plug Manufacturing, 1st International Scientific Conference of Engineering Sciences-3rd Scientific Conference of Engineering Science (2018).

DOI: 10.1109/isces.2018.8340555

[59] Muhsin. J Jweeg, Salah N Alnomani and Salah K Mohammad, Dynamic Analysis fo a Rotating Stepped Shaft with and without Defects, IOP Conference Series: Materials Science and Engineering, 3rd International Conference on Engineering Sciences, 671 (2020).

DOI: 10.1088/1757-899x/671/1/012004

[60] Kahtan Al-Khazraji, Jawad Kadhim and Payman Sahbah Ahmed, Tensile and Fatigue Characteristics of Lower-Limb Prosthetic Socket Made from Composite Materials, International Conference on Industrial Engineering and Operations Management (2012).

[61] Kahtan Al-Khazraji, Jawad Kadhim and Payman Sahbah Ahmed, Improving Mechanical and Fatigue Characteristic of Trans-Tibial Prosthetic Socket, International Conference on Industrial Engineering and Operations Management (2015).

[62] Muhsin J Jweeg and S Z Said, Effect of rotational and geometric stiffness matrices on dynamic stresses and deformations of rotating blades, Journal of the Institution of Engineers (India): Mechanical Engineering Division, 76 (1995) 29–38.

[63] Muhannad Al-Waily, Maher A R Sadiq Al-Baghdadi and Rasha Hayder Al-Khayat, Flow Velocity and Crack Angle Effect on Vibration and Flow Characterization for Pipe Induce Vibration, International Journal of Mechanical & Mechatronics Engineering, 17, 5 (2017).

[64] Mohsin Abdullah Al-Shammari, Experimental and FEA of the Crack Effects in a Vibrated Sandwich Plate, Journal of Engineering and Applied Sciences, 13, 17 (2018).

[65] Hussein I Mansoor, Mohsin Al-shammari and Amjad Al-Hamood, Theoretical Analysis of the Vibrations in Gas Turbine Rotor, IOP Conference Series: Materials Science and Engineering, 3rd International Conference on Engineering Sciences, 671 (2020).

DOI: 10.1088/1757-899x/671/1/012157

[66] S E Sadiq, S H Bakhy and M J Jweeg, Crashworthiness Behavior of Aircraft Sandwich Structure with Honeycomb Core under Bending Load, IOP Conference Series: Materials Science and Engineering (2020).

DOI: 10.1088/1757-899x/881/1/012046

[67] Jawad Kadhim Oleiwi and Shaymaa Jumaah Ahmed, Studying the Tensile and Buckling for PMMA Reinforced by Jute Fibers for Prosthetic Pylon, Engineering and Technology Journal, 34, 1 (2016).

DOI: 10.30684/etj.34.1a.10

[68] Jawad Kadhim Oleiwi, Shaymaa Jumaah Ahmed, Tensile and Buckling of Prosthetic Pylon Made from Hybrid Composite Materials, Engineering and Technology Journal, 34, 14 (2016).

DOI: 10.30684/etj.34.14a.9

[69] Rasha Hayder Al-Khayat, Maher A R Sadiq Al-Baghdadi, Ragad Aziz Neama and Muhannad Al-Waily, Optimization CFD Study of Erosion in 3D Elbow During Transportation of Crude Oil Contaminated with Sand Particles, International Journal of Engineering & Technology, 7, 3 (2018).

DOI: 10.14419/ijet.v7i3.14180

[70] Mohsin Abdullah Al-Shammari and Muhannad Al-Waily, Analytical Investigation of Buckling Behavior of Honeycombs Sandwich Combined Plate Structure, International Journal of Mechanical and Production Engineering Research and Development, 8, 4 (2018) 771–786.

DOI: 10.24247/ijmperdaug201883

[71] Marwah Ali Husain and Mohsin Abdullah Al-Shammari, Analytical Solution of Free Vibration Characteristics of Partially Circumferential Cracked Cylindrical Shell, Journal of Mechanical Engineering Research and Developments, 43, 3 (2020) 442–454.

[72] Suhair Ghazi Hussein, Mohsin Abdullah Al-Shammari, Ayad M Takhakh and Muhannad Al-Waily, Effect of Heat Treatment on Mechanical and Vibration Properties for 6061 and 2024 Aluminum Alloys, Journal of Mechanical Engineering Research and Developments, 43, 1 (2020).

[73] Ehab N Abbas, Muhannad Al-Waily, Tariq M Hammza and Muhsin J Jweeg, An Investigation to the Effects of Impact Strength on Laminated Notched Composites used in Prosthetic Sockets Manufacturing, IOP Conference Series: Materials Science and Engineering, 2nd International Scientific Conference of Al-Ayen University, 928 (2020).

DOI: 10.1088/1757-899x/928/2/022081

[74] Sadiq Emad Sadiq, Muhsin J Jweeg and Sadeq H Bakhy, The Effects of Honeycomb Parameters on Transient Response of an Aircraft Sandwich Panel Structure, IOP Conference Series: Materials Science and Engineering, 928 (2020).

DOI: 10.1088/1757-899x/928/2/022126

[75] Sadeq H. Bakhy and Muhannad Al-Waily, Development and Modeling of a Soft Finger in Robotics Based on Force Distribution, Journal of Mechanical Engineering Research and Developments, 44, 1 (2021) 382-395.

[76] Tammam Salim Naji Aswad, Mohd Azahari Bin Razali and Muhannad Al-Waily, Numerical Study of the Shape Obstacle Effect on Improving the Efficiency of Photovoltaic Cell, Journal of Mechanical Engineering Research and Developments, 44, 2 (2021) 209-224.

[77] Hayder Zaher Abdalikhwa, Mohsin Abdullah Al-Shammari, Emad Qasem Hussein, Characterization and Buckling Investigation of Composite Materials to be used in the Prosthetic Pylon Manufacturing, IOP Conference Series: Materials Science and Engineering, 1st International Conference on Sustainable Engineering and Technology, 1094 (2021).

DOI: 10.1088/1757-899x/1094/1/012170

[78] Muhsin J. Jweeg, H. A. Hamzah, Muhannad Al-Waily, Mohsin Abdullah Al-Shammari, A Finite Element Simulation of Nano Effects on Stress Distribution in a Below Knee Prosthetic, 4th International Conference on Engineering Sciences, IOP Conference Series: Materials Science and Engineering, 1067 (2021).

DOI: 10.1088/1757-899x/1067/1/012141

[79] Mohammed Hussein Kadhim Aljaberi, Maher AR Sadiq Al-Baghdadi, Muhannad Al-Waily, M Mohammadi-Aghdam, Taha Goudarzi, Numerical Investigation of Mechanical Behavior for Lattice Structure with Effect of Different Nanomaterial Types, IOP Conference Series: Materials Science and Engineering, 1094 (2021).

DOI: 10.1088/1757-899x/1094/1/012172

[80] Emad Kadum Njim, Muhannad Al-Waily, Sadeq H Bakhy, A Critical Review of Recent Research of Free Vibration and Stability of Functionally Graded Materials of Sandwich Plate, IOP Conference Series: Materials Science and Engineering, 1094 (2021).

DOI: 10.1088/1757-899x/1094/1/012081

[81] Rasha M Hussien and Mohsin Abdullah Al-Shammari, Optimization of Friction Stir Welded Aluminium Plates by the New Modified Particle Swarm Optimization, IOP Conference Series: Materials Science and Engineering, 1st International Conference on Sustainable Engineering and Technology, 1094 (2021).

DOI: 10.1088/1757-899x/1094/1/012156

[82] Emad Kadum Njim, Muhannad Al-Waily, Sadeq H. Bakhy, A Review of the Recent Research on the Experimental Tests of Functionally Graded Sandwich Panels, Journal of Mechanical Engineering Research and Developments, 44, 3 (2021) 420-441.

DOI: 10.1016/j.matpr.2021.03.235

[83] Zaman Abud Almalik Abud Ali, Ameer A. Kadhim, Rasha Hayder Al-Khayat, Muhannad Al-Waily, Review Influence of Loads upon Delamination Buckling in Composite Structures, Journal of Mechanical Engineering Research and Developments, 44, 3 (2021) 392-406.

[84] Ameer A. Kadhim, Esraa A. Abbod, Ahmed K. Muhammad, Kadhim K. Resan, Muhannad Al-Waily, Manufacturing and Analyzing of a New Prosthetic Shank with Adapters by 3D Printer, Journal of Mechanical Engineering Research and Developments, 44, 3 (2021) 383-391.

[85] Saddam K Al-Raheem, Muhsin J Jweeg, Abdul kareem F Hassan, Design and Construction of Device for Rubber Material Fatigue Test, IOP Conference Series: Materials Science and Engineering, 1st International Conference on Sustainable Engineering and Technology, 1094 (2021).

DOI: 10.1088/1757-899x/1094/1/012173

[86] Mohammed S Jabbar , Muhsin J Jweeg and Adnan I Mohammed, Numerical and Experimental Study of Elastic Recovery in Deep Drawing of Low Carbon and Galvanized Steel Sheet Conical Products, IOP Conference Series: Materials Science and Engineering, 1st International Conference on Sustainable Engineering and Technology, 1094 (2021).

DOI: 10.1088/1757-899x/1094/1/012155