New Polymer Composites Made of Recycled Polystyrene with Red Mud and Wind Blade Waste: An Industrial Ecology Case

Abstract:

The development of composites with the waste of industries close to each other would mean an interesting case of industrial symbiosis in search for using less financial and natural resources. This paper presents the development of polymer composites made of three types of waste, produced by industries located in the same region and distant at most 25 km from each other: electronic waste, red mud (obtained during aluminium production), and the waste of wind turbine blades' manufacturing (epoxy resin/glass fibre). Composites were obtained incorporating 5%, 10%, and 15% of industrial waste (red mud and epoxy/fibre) in a matrix of recycled high-impact polystyrene (HIPS) from discarded electronic equipment. Tests were performed to obtain the melt flow index and the composites' water content and study the mechanical properties (tensile and impact) of test specimens produced with the composites by injection moulding (temperature from 200 to 250°C, the injection pressure of 45 MPa, and the injection time of 2.5 s). Results showed that the composites have water content and melt flow index within the specifications for recycled HIPS and are usually more rigid than it, reaching values for Elasticity Modulus up to 34% higher. Therefore, these composites can be applied when materials with more stiffness than HIPS are required.

• Periodical: Materials Science Forum (Volume 1078)
• Pages: 201-212
• DOI: https://doi.org/10.4028/p-14mth5
• Online since: December 2022
• Authors: Juliana Thomaz Lefloch Barbosa*, Sandro Donnini Mancini, Cristina Belli, Maria Lucia Pereira Antunes, Jane Maria Faulstich de Paiva
• Keywords: Epoxy Resin, Glass Fibre, HIPS, Industrial Ecology, Polymer Composite, Red Mud

References

[1] Ellen Macarthur Foundation. Circular economy introduction. (2022). https://ellenmacarthurfoundation.org/topics/circular-economy-introduction/overview.

DOI: 10.1007/978-981-15-8510-4_20

[2] F. Pomponi, A. Moncaster, Circular economy for the built environment: a research framework, J Clean Prod. 143 (2017) 710-718.

DOI: 10.1016/j.jclepro.2016.12.055

[3] W.R. Stahel, Circular economy, Nature. 531 (2016) 435-438.

[4] G. Power, M. Gräfe, C. Klauber, Bauxite residue issues: I: current management, disposal and storage practices, Hydrometallurgy. 108 (2011) 33-45.

DOI: 10.1016/j.hydromet.2011.02.006

[5] S.S. Rath, P. Archana, K. Jayasankar, A.K. Mitra, C.S Kumar, P.S. Mukherjee, B.K Mishra, Statistical modeling studies of iron recovery from red mud using thermal plasma, Plasma Sci Technol. 15 (2013) 459-464.

DOI: 10.1088/1009-0630/15/5/13

[6] Red Mud Project. (2006). https://redmud.org/red-mud/disposal/.

[7] H.L. Hendricks, V.E. Buchanan, Effect of material parameters on the mechanical properties of chemically treated red mud HDPE composites, Polymers and Polymer Composites. 29(8) (2011) 1126–1134.

DOI: 10.1177/0967391120954064

[8] A. Gelencsér, N. Kováts, B. Turóczi, Á. Rostási, A. Hoffer, K. Imre, I. Nyirő-Kósa, D. Csákberényi-Malasics, Á. Tóth, A. Czitrovszky, A. Nagy, S. Nagy, A. Ács, A. Kovács, Á. Ferincz, Z. Hartyáni, M. Pósfai, The red mud accident in Ajka (Hungary): Characterisation and potencial health effects of fugitive dust, Environ Sci Technol. 45 (2011) 1608-1615.

DOI: 10.1021/es104005r

[9] E.B. Silva Filho, M.C.M Alves, M. Motta, E.H.C Oliveira, W. Brander Junior, Study on the use of red mud for removal of dyes from textile effluents, Quim Nova. 31 (2008) 985-989.

[10] S.R. Naqvia, H. Mysore Prabhakaraa, E.A Bramera, W. Dierkesa, R. Akkermanb, G. Brema, A critical review on recycling of end-of-life carbon fibre/glass fibre reinforced composites waste using pyrolysis towards a circular economy, Resour Conserv Recy. 136 (2018) 118-129.

DOI: 10.1016/j.resconrec.2018.04.013

[11] R.S Chen, S. Ahmad, S. Gan, M.N Salleh, M.H. Ag Ghani, M.A. Tarawneh, Effect of polymer blend matrix compatibility and fibre reinforcement content on thermal stability and flammability of ecocomposites made from waste materials, Thermochim Acta. 640 (2016) 52–61.

DOI: 10.1016/j.tca.2016.08.005

[12] Winde Europe. Circular Economy: Blade recycling is a top priority for the wind industry. (2020). https://windeurope.org/newsroom/news/blade-recycling-a-top-priority-for-the-wind-industry/.

[13] Casper Star-Tribune. Wind turbine blades in coal mine pits? There's a new law in Wyoming to allow it. (2020). https://trib.com/business/energy/wind-turbine-blades-in-coal-mine-pits-theres-a-new-law-in-wyoming-to-allow/article_df17dbc9-f6db-5eb6-8164-32b25275aa9b.htm.

[14] Electrek. World's first wind turbine with recyclable blades is up and spinning. (2022). https://electrek.co/2022/08/02/worlds-first-wind-turbine-with-recyclable-blades-is-up-and-spinning/.

[15] D. Coughlan, C. Fitzpatrick C, M. McMahon, Repurposing end of life notebook computers from consumer WEEE as thin client computers – A hybrid end of life strategy for the Circular Economy in electronics, J Clean Prod. 192 (2018) 809-820.

DOI: 10.1016/j.jclepro.2018.05.029

[16] P.R. Valério. Evaluation of the environmental impacts of electronic equipment by materials inventory. Sorocaba: Sorocaba São Paulo State University (Unesp). (2014).

[17] Y.M.B. Saavedra, D.R. Iritani, A.L.R. Pavan, A.R. Ometto, Theoretical contribution of industrial ecology to circular economy, J Clean Prod. 170 (2018) 1514-1522.

DOI: 10.1016/j.jclepro.2017.09.260

[18] ABNT NBR NM248 (2003) Aggregates – Brazilian standard for particle-size distribution determination. ABNT, Rio de Janeiro.

[19] ASTM 6913 (2017) Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis. ASTM International, West Conshohocken.

DOI: 10.1520/d6913-04r09

[20] ASTM D3171 (2015) Standard Test Methods for Constituent Content of Composite Materials. ASTM International, West Conshohocken.

[21] D.S. Costa Et al.: Utilization of red mud and vegetalble fiber –sisal and jute- in polymeric composites. Abstract for paper presented at the Brazilian Congresso of Ceramics, Águas de Lindoia, Brazil (2016).

[22] V.A. Prabu, S. Kalirasu, M. Uthayakumar, V. Manikandan: Processing and characterisation of red mud filled sisal fiber reinforced polymer composite. Abstract for paper presented at the IEEE-International Conference On Advances In Engineering, Science And Management, Nagapattinam, India (2012).

[23] V.A. Prabu, S. Kalirasu, M. Uthaykumar, V. Manikandan, Investigation of the mechanical properties on red mud filled polyester banana composites using grey relational technique, Mater Phys Mech. 14 (2012) 57-63.

[24] ASTM D570 (1998) Standard Test Methods: Water absorption of plastics. ASTM International, West Conshohocken.

[25] ASTM D1238 (2013) Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer. ASTM International, West Conshohocken.

DOI: 10.1520/d1238-10

[26] ASTM D638 (2014) Standard Test Method for Tensile Properties of Plastics. ASTM International, West Conshohocken.

[27] ASTM D256 (2018) Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics. ASTM International, West Conshohocken.

[28] M.L.P. Antunes, S.J. Couperthwaite, F.T. Conceição, C.P.C. Jesus, P.K. Kiyohara, A.C.V. Ceolho, R.L. Frost, Red Mud from Brazil: Thermal Behavior and Physical Properties, Ind Eng Chem Res. 51 (2012) 775 – 779.

DOI: 10.1021/ie201700k

[29] R.C.C Costa, F.C.C. Moura, P.E.F. Oliveira, F. Magalhães, J.D. Adirsson, R.M. Lago Controlled reduction of red mud waste to produce active systems for environmental applications: Heterogeneous Fenton reaction and reduction of Cr(VI), Chemosphere. 78 (2010) 1116–1120.

DOI: 10.1016/j.chemosphere.2009.12.032

[30] E.P. Manfroi, M. Chieraf, J.C. Rocha, Microstructure, mineralogy and environmental evaluation of cementitious composites produced with red mud waste, Constr Build Mater. 67 (2014) 29-36.

DOI: 10.1016/j.conbuildmat.2013.10.031

[31] D.V. Ribeiro, J.A. Labrincha, M.R. Morelli, Effect of the addition of red mud on the corrosion parameters of reinforced concrete, Cement Concrete Res.42 (2012) 124–133.

DOI: 10.1016/j.cemconres.2011.09.002

[32] Sinctronics. Sustainability Report. (2021). http://sinctronics.com.br/wp-content/uploads/2021/07/312_relatorio-anual_2020_sinctronics_a4_final-digital.pdf.

[33] Y. Zhang, Y. QU, S. WU, apud apud Y. Liu, R. Naidu, H. Ming, Red mud as an amendment for pollutants in solid and liquid phases, Geoderma. 163 (2001) 1–12.

DOI: 10.1016/j.geoderma.2011.04.002

[34] E.J.S. Cunha, R.M. Miranda, J.A.S. Souza, M.Jr.A. Oliveira: Influence of the addition of red mud from Bayer process in polymer matrixes of isophthalix polyester. Abstract for paper presented at the International Comitee for the Study of Bauxite Alumina Aluminium, Zhengzhou, China (2012).

[35] H. Jena, A.K. Sataphaty: Fabrication mechanical characterization and wear response of hybrid composites filed with red mud: an alumina plant waste. Abstract for paper presented at the 5th International Conference on Advances in Mechanical Engineering, Gujarat, India (2011).