Observation of Internal Fatigue Cracks in Repeatedly Induction-Heated S45C Bearing Steel under Rotating Bending Fatigue

Abstract:

Induction-heated steel has hard and soft layers. These layers can cause an internal fatigue crack originating from the boundary of these layers when cyclic stress is applied. Repeated heating is known as a method for improving fatigue strength, and it was applied to induction heating method. Repeatedly induction-heated steel had high fatigue strength compared to single quenching. We performed rotating bending fatigue tests of low carbon steel (JIS-S45C) induction-heated three times, and observed the fracture surfaces and the microstructures of internal fatigue cracks. The internal fatigue cracks originated from the area around the boundary between soft and hard layers surrounding crack origin. Some pearlite and ferrite can be seen. There were pearlite and dimples on the soft layer of internal fatigue crack and clear grains on the hard layer of the crack. From chase-up observation, we revealed that internal fatigue crack originated from soft layer.

• Periodical: Materials Science Forum (Volume 1086)
• Pages: 93-98
• DOI: https://doi.org/10.4028/p-t1mle1
• Online since: April 2023
• Authors: Shusuke Kita, Li Xiang, Takahiro Matsueda, Koshiro Mizobe*, Katsuyuki Kida
• Keywords: Fracture Surface, Induction Heating, Repeated Heating, Rotating Bending Fatigue, S45C Steel

References

[1] P. H. Frith, Fatigue Tests on Rolled Alloy Steels Made in Electric and Open-Hearth Furnaces, Journal of The Iron and Steel Institute, Vol. 180, pp.26-33, (1955).

[2] K. Shiozawa, Y. Morii, S. Nishino and L. Lu, Subsurface crack initiation and propagation mechanism in high-strength steel in a very high cycle fatigue regime, International Journal of Fatigue, 28, pp.1521-1532, (2006).

DOI: 10.1016/j.ijfatigue.2005.08.015

[3] Y. Murakami, Metal fatigue: Effects of Defects and Nonmetallic Inclusions, Elsevier Science Ltd, UK, (2002).

[4] T. Sakai, Y. Sato, Y. Nagano, M. Takeda and N. Oguma, Effect of stress ratio on long life fatigue behavior of high carbon chromium bearing steel under axial loading, International Journal of Fatigue, 28, pp.1547-1554, (2006).

DOI: 10.1016/j.ijfatigue.2005.04.018

[5] R. A. Grange, E. R. Shackelford, U. S. Patent 3,178,324, (1965).

[6] R. A. Grange, The Rapid Heat Treatment of Steel, Merallurgical Transactions, Vol. 2, pp.65-78, (1971).

[7] C. Ooki, K. Maeda and H. Nakashima, Improving Rolling Contact Fatigue Life of Bearing Steels Through Refinement, NTN TECHNICAL REVIEW, No. 71, pp.2-7, (2004).

DOI: 10.4271/2004-01-0634

[8] H. Koike, E.C. Santos, K. Kida T. Honda and J. Rozwadowska, Effect of repeated induction heating on fatigue crack propagation in SAE 52100 bearing steel, Advanced Materials Research, Vols. 217-218, pp.1266-1271, (2011).

DOI: 10.4028/www.scientific.net/amr.217-218.1266

[9] K. Mizobe, E. C. Santos, T. Honda, H. Koike and K. Kida, Observation of non-metallic inclusions on repeatedly quenched SAE 52100 bearing steel fracture surfaces, International Jornal of Materials and Product Technology, Vol. 44, pp.227-239, (2012).

DOI: 10.1504/ijmpt.2012.050186

[10] K. Tsuji, K. Mizobe, and K. Kida, Development of Surface Etching (FSE) Method around Non-Metallic Inclusion of SUJ2 Steel, Material Science Forum, Vol. 971, pp.65-69, (2019).

DOI: 10.4028/www.scientific.net/msf.971.65

[11] I. Yoshida, K. Mizobe and K. Kida, Observation of Fracture Surface of Induction-Heated JIS SUJ2 Bearing Steel under Rotating Bending Fatigue, ISSN: 1662-9752, Vol. 904 pp.24-28, (2017).

DOI: 10.4028/www.scientific.net/msf.904.24

[12] K. Mizobe, M. Matsushita, T. Shibukawa and K. Kida, Observation of Cracks Originating from Transition Area in Induction-Heated S45CShaft under Rotating Bending Fatigue, Key Engineering Materials, Vol. 832, pp.3-9, (2020).

DOI: 10.4028/www.scientific.net/kem.832.3