Optimization of Processing Conditions on the Wire Electric Discharge Machining by the Parameters of Vibro-Acoustic Signal

S.N. Grigoriev; Mikhail Pavlovich Kozochkin; Artur Nikolaevich Porvatov

doi:10.4028/www.scientific.net/MSF.876.36

Paper Titles

Methods for Characterizing Properties of Corrosion-Resistant Steel Powders Used for Powder Bed Fusion Processes
p.1

Features of Vibro-Acoustic Monitoring EDM of Conductive Ceramics
p.8

New Method for Synthesis of Hard Coatings Using Pulsed Bombardment with High-Energy Gas Atoms
p.14

Synthesis of Hard-Melting Carbide, Nitrite and Intermetallic Phases with Surface Electron-Beam Microallоying
p.25

Optimization of Processing Conditions on the Wire Electric Discharge Machining by the Parameters of Vibro-Acoustic Signal
p.36

Specifics of Wear of Ceramic Cutting Tool Inserts Featuring Al₂O₃-TiC Dies when Face Milling Hardened Cast Iron
p.43

Effect of Wear of Tool Cutting Edge on Detail Surface Layer Deformation and Parameters of Vibro-Acoustic Signals
p.50

Influence of Carbide Substrate Properties on Wear Resistance of Tool with Multilayer Coating in Machining of Chromium-Based Heat-Resistant Alloy
p.59

Tracking Navigation System Based on Photogrammetry Principles
p.69

HomeMaterials Science ForumMaterials Science Forum Vol. 876Optimization of Processing Conditions on the Wire...

Optimization of Processing Conditions on the Wire Electric Discharge Machining by the Parameters of Vibro-Acoustic Signal

Abstract:

The results of the research of vibro-acoustic signals, accompanying the processes of electrical discharge machining and pulsed laser treatment, are presented in this article. It is shown that the monitoring parameters of vibro-acoustic signals can improve the quality of management spark erosion equipment.

You might also be interested in these eBooks

Innovative Methods in Machining and Advanced Materials

View Preview

Info:

Periodical:

Materials Science Forum (Volume 876)

Pages:

36-42

DOI:

https://doi.org/10.4028/www.scientific.net/MSF.876.36

Citation:

Cite this paper

Online since:

October 2016

Authors:

S.N. Grigoriev, Mikhail Pavlovich Kozochkin, Artur Nikolaevich Porvatov*

Keywords:

Bit Pulses, Dynamic Characteristics, Monitoring, Signal Spectrum, Spark-Erosion, Vibro-Acoustics

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] B.G. Gutkin, Automated EDM , L., Mechanical engineering, (1971).

Google Scholar

[2] B.A. Artamonov and Yu.S. Volkov Analiz modelei elektrokhimicheskoi i elektroerozionnoi obrabotki. Chast' 2, Modeli protsessov elektroerozionnoi obrabotki. Provolochnaya vyrezka (Analysis of Models of Electrochemical and Electrodischarge Treatment, Part 2: Models of Electrodischarge Treatment. Wire Cutting), Moscow, Vseross. Nauchno-issled. Inst. Patent. Inform., (1991).

Google Scholar

[3] S.N. Grigor'ev, M.P. Kozochkin, Improvement of Machining by the Vibroacoustic Diagnostics of Electrophysical Processes, Russian Engineering Research. 35 No. 11 (2015) 801–806.

DOI: 10.3103/s1068798x15110064

Google Scholar

[4] M.P. Kozochkin, S.N. Grigor'ev, A.A. Okun'kova, A.N. Porvatov, Monitoring of Electric Discharge Machining by Means of Acoustic Emission, Russian Engineering Research. 36 No. 3 (2016) 244–248.

DOI: 10.3103/s1068798x16030114

Google Scholar

[5] S.N. Grigor'ev, M.P. Kozochkin, S.V. Fedorov, A.N. Porvatov, A.A. Okun'kova, Study of Electroerosion Processing by Vibroacoustic Diagnostic Methods, Measurement Techniques. 58 No. 8 (2015) 878-884.

DOI: 10.1007/s11018-015-0811-2

Google Scholar

[6] M.V. Korenblyum, M.L. Levit, and A.L. Livshits, Adaptivnoe upravlenie elektroerozionnymi stankami (Adaptive Control of EDM Machines), Moscow: Nauch. Issled. Inst. Mashinostr., (1977).

Google Scholar

[7] E.F. Nemilov, Spravochnik po elektroerozionnoi obrabotke materialov (Handbook on Electrodischarge Treatment of Materials), Leningrad: Mashinostroenie, (1989).

Google Scholar

[8] S.N. Grigoriev, M.P. Kozochkin, F.S. Sabirov, A.A. Kutin, Diagnostic systems basis for technological improvemrnt, Procedia CIRP. 1 (2012) 599-604.

DOI: 10.1016/j.procir.2012.05.006

Google Scholar

[9] M.P. Kozochkin, Nonlinear cutting dynamics, Russian Engineering Research. 32 (4) (2012) 387-391.

Google Scholar

[10] S.N. Grigoriev, M.P. Kozochkin, F.S. Sabirov and V.A. Sinopal'nikov, Modern problems of technical diagnostics of machine tools, Vestn. Mosk. Gos. Tekhnol. Univ., Stankin. No. 4 (2010) 27-36.

Google Scholar

[11] L. Tony, K. Schmitz, Scott Smith, Machining Dynamics. Frequency Response to Improved Productivity, Springer US, New York, (2009).

Google Scholar

[12] Y. Altintas, Manufacturing Automation: Metal Cutting Mechanics, Machine Tool Vibrations, and CNC Design, Cambridge University Press, Cambridge, (2000).

DOI: 10.1017/cbo9780511843723

Google Scholar