Spectral Parameters of Straightness Deviation Evaluation

Abstract:

Spectral analysis of different profiles obtained during straightness deviation measurement was performed. The several profiles are showed, for which the value of straightness deviation is the same, but its behavior differs greatly. Spectral parameters characterizing the type of straightness deviation are proposed. The automated system based on factors of fuzzy-set theory with implementation in the form of neural network is developed.

• Periodical: Materials Science Forum (Volume 876)
• Pages: 74-79
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.876.74
• Online since: October 2016
• Authors: Alexander Vladimirovich Glubokov*, Svetlana Vladimirovna Glubokova, Alexey Vileninovich Shulepov, Sergey Evgenievich Ped
• Keywords: Form Deviations, Fuzzy-Set Theory, Measurement, Spectral Analysis, Straightness Deviation

References

[1] S.N. Grigoriev, V.I. Teleshevskii, A.V. Glubokov, S.E. Ped, S.V. Glubokova, The problems of metrological support for the preparation of production in machine construction, Measurement Techniques 55 (2012) 526-529.

DOI: 10.1007/s11018-012-9993-z

[2] R. Schmitt, N. Konig, GF. Mallmann, F. Depiereux, Fiber-optical measurement of form deviations of rotation-symmetric parts, Measurement 43 (2012) 714-718.

DOI: 10.1016/j.measurement.2010.01.014

[3] S.N. Grigoriev, V.I. Teleshevskii, Measurement problems in technological shaping processes, Measurement Techniques 54 (2011) 744-749.

DOI: 10.1007/s11018-011-9798-5

[4] D.A. Masterenko, P.N. Emel'yanov, M.G. Koval'skii, A. Yu. Baikovskii, S. Yu. Alabin, Development of a Device for Measurement of the Deviations of the Form and Roughness of the Surfaces of Ultra-Precise Parts, Measurement Techniques 57 (2014).

DOI: 10.1007/s11018-014-0442-z

[5] V.I. Teleshevskii, A.V. Glubokov, A computerized data acquisition system for measuring planarity deviations with electronic levels, Measurement Techniques 47 (2004) 1055-1060.

DOI: 10.1007/s11018-005-0058-4

[6] S.N. Grigoriev, S.G. Konov, Development of three-dimensional metrology for control of composite surfaces in mechanical engineering, Testing. Diagnostic 12 (2012) 9-13. [in Russian].

[7] A.V. Glubokov, S.E. Ped, Investigation of the methodological error of measurement of deviations from straightness, Vestnik MSTU "STANKIN, 37 (2016) 71-75.

[8] X.J. Jiang, H.J. Huang, X.Z. Wang, A.J. Zeng, Measurement of surface form deviation of the plane optical element using grid line method, OPTIC 121 (2010) 1133-1137.

DOI: 10.1016/j.ijleo.2008.12.024

[9] B.M. Colosimo, G. Moroni, S. Petro, A tolerance interval based criterion for optimizing discrete point sampling strategies, Precision engineering-journal of the international societies for precision engineering and nanotechnology 34 (2010).

DOI: 10.1016/j.precisioneng.2010.04.004

[10] S.E. Ped, Investigation of the procedure error of coordinate measurements of the geometric parameters of machine parts, Measurement Techniques 57 (2014) 266-272.

DOI: 10.1007/s11018-014-0443-y

[11] M. Magdziak, An Algorithm of Form Deviation Calculation in Coordinate Measurements of Free-Form Surfaces of Products, Strojniski vestnik-journal of mechanical engineering 62 (2016) 51-59.

DOI: 10.5545/sv-jme.2015.3039

[12] B. Hassibi, A.H. Sayed, T. Kailath, The H infinity optimality of the LMS algorithm, IEEE Transactions on Signal Processing 44 (1996) 267-280.

DOI: 10.1109/78.485923

[13] V.I. Teleshevskii, A.V. Glubokov, S.V. Glubokova, The automated choice of methods and instruments for measuring deviations of arrangement, Measurement Techniques 55 (2012) 637-642.

DOI: 10.1007/s11018-012-0013-0

[14] S.V. Glubokova, Neural Networks application for measuring methods selection for geometric elements orientation deviations, Vestnik MSTU "STANKIN, 29 (2014) 63-67.