Manufactured Process of High Strength and High Electrical Conductivity Cu-Cr-Zr-Mg Alloy Bars

Chun Lei Gan; Hui Liu; Kaihong Zheng; Yu Ning Liu; Hai Yan Wang

doi:10.4028/www.scientific.net/MSF.898.1215

Paper Titles

Preparation of Micro-Hole with Large Aspect Ratio
p.1190

Effects of Austenitizing Temperature and Cooling Rate on the Mechanical Properties of 36MnVS4 Steel for Automobile Engine Connecting Rod
p.1195

Influence of Cooling Rate and Chemical Composition on Phase Transformation and Hardness of C70S6 Steel
p.1202

Common Defect Analysis for Large Section Special Steel Forging
p.1208

Manufactured Process of High Strength and High Electrical Conductivity Cu-Cr-Zr-Mg Alloy Bars
p.1215

Preparation and Fundamental Research of Continuous Through-Porous Pure Aluminum Flat Pipes by Depoling Continuous Casting
p.1220

Grain Refinement Mechanism and Effective Nucleation Phase of Al-5Ti-1B Master Alloy
p.1231

Effect of High Density Electropulsing Current on Microstructure and Mechanical Properties of Fe-6.5wt.%Si Alloy Sheet
p.1236

Microstructure and Magnetic Properties of (Nd_1-2xPr_xY_x)_2.28Fe_13.58B_1.14 Melt-Spun Alloys
p.1242

HomeMaterials Science ForumMaterials Science Forum Vol. 898Manufactured Process of High Strength and High...

Manufactured Process of High Strength and High Electrical Conductivity Cu-Cr-Zr-Mg Alloy Bars

Abstract:

A typical process was developed to manufacture Cu-Cr-Zr-Mg alloy bars with high strength and high electrical conductivity. The microstructure and properties of the alloys were investigated by observations of optical microscopy and scanning electron microscopy, and measurements of tensile strength and electrical conductivity. The results showed that the process and thermo mechanical treatments were successfully developed to manufacture Cu-Cr-Zr-Mg alloy bars with good combinations of the ultimate tensile strength (602.5 MPa) and conductivity (85.4% IACS). The achievement of high strength and high electrical conductivity in the alloy could be ascribed to the interactions of strain hardening and precipitation hardening.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Materials Science Forum (Volume 898)

Pages:

1215-1219

DOI:

https://doi.org/10.4028/www.scientific.net/MSF.898.1215

Citation:

Cite this paper

Online since:

June 2017

Authors:

Chun Lei Gan*, Hui Liu, Kaihong Zheng, Yu Ning Liu, Hai Yan Wang

Keywords:

Cu-Cr-Zr-Mg Alloy, High Electrical Conductivity, High Strength

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] S.J. Zhang, R.G. Li, H.J. Kang, Z.N. Chen, W. Wang, C.L. Zou, T.J. Li, T.M. Wang, A high strength and high electrical conductivity Cu-Cr-Zr alloy fabricated by cryorolling and intermediate aging treatment, Mater. Sci. Eng. A 680 (2017) 108-114.

DOI: 10.1016/j.msea.2016.10.087

Google Scholar

[2] J.H. Su, Q.M. Dong, P. Liu, H.J. Li, B.X. Kang, Research on aging precipitation in a Cu-Cr-Zr-Mg alloy, Mater. Sci. Eng. A 392 (2005) 422-426.

DOI: 10.1016/j.msea.2004.09.041

Google Scholar

[3] A. Papillon, S. Roure, H. Schellekens, J.M. Missiaen, J.M. Chaix, Emmanuel Rigal, Investigation on the chemical reactions affecting the sinterability and oxide content of Cu-Cr composites during the solid state sintering process, Mater. Des. 113 (2017).

DOI: 10.1016/j.matdes.2016.09.038

Google Scholar

[4] G. Sudarshan Rao, V.M.J. Sharma, S. Ganesh Sundara Raman, M. Amruth, P. Ramesh Narayanan, S.C. Sharma, P.V. VenkitaKrishnan, Effects of temperature and strain rate on tensile properties of Cu-Cr-Zr-Ti Alloy, Mater. Sci. Eng. A 668 (2016) 97-104.

DOI: 10.1016/j.msea.2016.05.035

Google Scholar

[5] S. Chenna Krishna, G. Sudarsana Rao, Abhay K. Jha, Bhanu Pant, P.V. Venkitakrishnan, Strengthening in high strength Cu-Cr-Zr-Ti alloy plates produced by hot rolling, Mater. Sci. Eng. A 674(2016)164-170.

DOI: 10.1016/j.msea.2016.07.063

Google Scholar

[6] H. Fernee, J. Nairn, A. Atrens, Cold worked Cu-Fe-Cr alloys, J. Mater. Sci. 36 (2001) 5497-5510.

DOI: 10.1023/a:1012414605163

Google Scholar