The Influence of Temperature and Deformation Ratio on Structure Formation and Physico-Mechanical Properties of Powder Materials

Abstract:

The paper presents the materials on researching the use of current conductor copper waste for getting new functional materials. The changes of maximum deformation ratio, density, microstructure and hardness of powder copper preforms at different temperatures and deformation rates have been studied. The result is that the value of the maximum deformation ratio depends on kinetics of dynamic weakening processes. The change of the microstructure depending on the temperature and deformation ratio has been scrutinized. It has been established that the most fine-grained structure was got at the temperatures of dynamical recovery and recrystallization. The temperature intervals of stamping for manufacturing products by pressing are recommended. On the basis of experimental researches a resource-saving manufacturing method of producing axisymmetric details of high density from powder copper material with the use of maximum deformation ratios has been elaborated.

• Periodical: Materials Science Forum (Volume 989)
• Pages: 270-275
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.989.270
• Online since: May 2020
• Authors: Lyudmila Ryabicheva, Valery V. Dyadichev*, Yu.N. Nikitin, A.V. Dyadichev
• Keywords: Density, Hardness, Industrial Waste, Microstructure, Powder Copper Preform, Recovery, Recrystallization

References

[1] M. Ramesh, K. Karthic, T. Karthikeyan, A. Kumaravel, Construction materials from industrial wastes - A review of current practices, International Journal of Environmental Research and Development. Vol. 4, 4 (2014) 317-324.

[2] R. Dachowskia, P. Kostrzewaa, The use of waste materials in the construction industry, Procedia Engineering. 161 (2016) 754-758.

[3] Yu.G. Dorofeev, V.I. Miroshnikov, E.S. Baidala, The main parameters of the technology of dynamic hot pressing in the production of parts of varying degrees of complexity, Powder metallurgy. 8 (1979) 91-99.

DOI: 10.1007/bf00791408

[4] L.A. Ryabicheva, A.T. Cirkin, Yu.A. Losev, Patent 47841 А Ukraine, MPK 7 В22 F9/02, Н01 В15/00, No 2234683056, Method of processing of a scrap of copper conductors of current, Publ. (2002).

[5] L.A. Ryabicheva, A.T. Cirkin, Yu.M. Nikitin, M.V. Beloshitsky, N.V. Avsenyova, Patent 12618 А Ukraine, MPK 7 F41G3/16 B22F3/16, No 200508199, A method of making dense products of copper powder, (2006).

[6] L.V. Popivnenko, Antifriction materials obtained by pressing powders and their application, Improvement of processes and equipment for pressure treatment in metallurgy and machine building: Thematic collection of scientific works, Kramatorsk: DDMA, (2001) 405-411.

[7] L.A. Ryabicheva, Yu.N. Nikitin, T.V. Vasilenko, Investigation of half-hot deformation of porous billets of powdered copper, Resource-production technologies of technology and processing with a squeeze of material at machine-drilling equipment: Coolection of scientific works. etc., in 2 parts, part 1, Lugansk: V. Dahl SNU Publishing house, (2004) 90-96.

[8] E.S. Sevastyanov, P.N. Kireev, On dynamic strain aging of powder alloys Cu - Ti, Powder metallurgy. 2 (1986) 78-83.

DOI: 10.1007/bf00805614

[9] V.A. Pavlov, M.I. Nosenko, B.V. Popov, S.N. Yakunin, Changing the deformation characteristics of porous blanks of powders of titanium, copper and aluminum, Powder metallurgy. 9 (1987) 20-24.

DOI: 10.1007/bf00797174

[10] G.M. Volkogonov, A.M. Dmitriev, E.P. Dobryakov et al., Progressive technological processes of stamping parts from powders and equipment, Ed. by A.M. Dmitrieva, A.G. Ovchinnikova, Moscow: Mechanical Engineering, (1991).

[11] Yu.G. Dorofeev, V.V. Sinelshchikov, Features of deformation and cracking of heated cylindrical powder blanks, Powder metallurgy. 1 (1980) 25-30.

DOI: 10.1007/bf00798156

[12] G. W. Cull, Mechanical properties of powder forgings, Powder Met. Vol.18, 32 (1975) 165-167.

[13] Yu. G. Dorofeev, Dynamic hot pressing of powder blanks, Moscow: Metallurgy, (1977).

[14] L. Ryabicheva, D. Usatuk, Yu. Nikitin, The influence of warm deforming modes on compaction of porous copper billets, Third international conference & exibition on powder metallurgy, RoPM 2005, Technical University of Cluj-Napoca, ROMANIA (2005) 224-226.

[15] L. A. Ryabicheva, Item-by-Element Control of Structure Formation in Technological Processes of Hot Forming, Lugansk: VUGU Publishing House, (1996).

[16] M. S. Kovalchenko, Theoretical Foundations of Hot Pressure Treatment of Porous Materials, Kiev: Naukova Dumka, (1980).

[17] L. Ryabicheva, A. Tsirkin, D. Usatyuk, Warm deforming of copper porous powder billets, Commission of motorization and power industry in agriculture Lublin university of technology, Volodymyr Dal East-Ukrainian National university of Lugansk, Lublin (2010) 134-140.

[18] V.I. Alimov, L.A. Ryabicheva, V.V. Dyadichev, S.G. Menyuk, A.V. Dyadichev, Corrosion and Corrosion Protection of Materials, Monograph: Simferopol: Antiqua LLC, (2019).

[19] V. Dyadichev, A. Kolesnikov, A. Dyadichev, S. Menyuk and E. Dyadicheva, Model of creation a multilayer structure for production of building pipes, Journal MATEC Web Conf.: Proceedings of VI International Scientific Conference Integration, Partnership and Innovation in Construction Science and Education, - IPICSE-2018. 251 (2018) Art. No 251 01006.

DOI: 10.1051/matecconf/201825101006

[20] L. Ryabicheva, D. Usatyuk, The influence of pressing parameters to the structure and properties of high density copper products, The International congress and exhibition EURO PM 2009 proceedings. 2 (2009) 1230-1235.