Thermal Processes Simulation during Processing Bevel Gears

Abstract:

In the article the model for forecasting of thermal processes arising during processing of bevel gears is presented. The kinematics of cutting is modeled due to the analytical model. Chipping is modeled using the finite element method. The experiment is based on the method of infrared photography of the cutting process. In the process of carrying out a numerical experiment, the graphs of the heat fields for the tool, the workpiece gear and chips were obtained, and an array of data on their change during the cutting process was achieved. The simulation results showed that the maximum temperatures and heat flows in the tool depend significantly on the choice of the rake and clearance angels of the cutting.

• Periodical: Solid State Phenomena (Volume 284)
• Pages: 495-500
• DOI: https://doi.org/10.4028/www.scientific.net/SSP.284.495
• Online since: October 2018
• Authors: N. Kanatnikov*, P. Kanatnikova, D. Pickalov
• Keywords: Analytical Modeling of Cutting Process, Bevel Gear, Cutting, Cutting Temperature, Numerical Simulation of Cutting Process, Thermal Flows

References

[1] P. J. Arrazola, et al, Recent advances in modelling of metal machining processes, CIRP Annals-Manufacturing Technology. 62.2 (2013) 695-718.

DOI: 10.1016/j.cirp.2013.05.006

[2] Komanduri, Ranga, and Zhen Bing Hou, Thermal modeling of the metal cutting process: Part I-Temperature rise distribution due to shear plane heat source, International Journal of Mechanical Sciences. 42.9 (2000) 1715-1752.

DOI: 10.1016/s0020-7403(99)00105-8

[3] Huang, Yong, and S. Y. Liang, Cutting forces modeling considering the effect of tool thermal property-application to CBN hard turning, International journal of machine tools and manufacture. 43.3 (2003) 307-315.

DOI: 10.1016/s0890-6955(02)00185-2

[4] Karpat, Yiğit, and Tuğrul Özel, Predictive analytical and thermal modeling of orthogonal cutting process-part I: predictions of tool forces, stresses, and temperature distributions, Journal of manufacturing science and engineering. 128.2 (2006).

DOI: 10.1115/1.2162590

[5] M'Saoubi, Rachid, and Hariharan Chandrasekaran, Experimental study and modelling of tool temperature distribution in orthogonal cutting of AISI 316L and AISI 3115 steels, The International Journal of Advanced Manufacturing Technologyб 56.9-12 (2011).

DOI: 10.1007/s00170-011-3257-y

[6] G. Barsukov, T. Zhuravleva, O. Kozhus, Increasing Of Efficiency Of Environmentally Friendly Technology Of AWJ Of A Glass Fiber Plastic, IOP Conf. Series: Earth and Environmental Science. 50 (2017) 012001.

DOI: 10.1088/1755-1315/50/1/012001

[7] Karpat, Yiğit, and Tuğrul Özel, Analytical and thermal modeling of high-speed machining with chamfered tools, Journal of Manufacturing Science and Engineering. 130.1 (2008) 011001.

DOI: 10.1115/1.2783282

[8] J. C. Outeiro, et al, Analysis of residual stresses induced by dry turning of difficult-to-machine materials, CIRP Annals-Manufacturing Technology. 57.1 (2008) 77-80.

DOI: 10.1016/j.cirp.2008.03.076

[9] T. Özel, et al, Investigations on the effects of multi-layered coated inserts in machining Ti-6Al-4V alloy with experiments and finite element simulations, CIRP Annals-Manufacturing Technology. 59.1 (2010) 77-82.

DOI: 10.1016/j.cirp.2010.03.055

[10] Davies, A. Matthew, et al, On the measurement and prediction of temperature fields in machining AISI 1045 steel, CIRP Annals-Manufacturing Technology. 52.1 (2003) 77-80.

DOI: 10.1016/s0007-8506(07)60535-6

[11] Arrazola, et al, The effect of machinability on thermal fields in orthogonal cutting of AISI 4140 steel, CIRP Annals-Manufacturing Technology. 57.1 (2008) 65-68.

DOI: 10.1016/j.cirp.2008.03.139

[12] Davoodi, Behnam, and Ahmadreza Hosseini Tazehkandi, Experimental investigation and optimization of cutting parameters in dry and wet machining of aluminum alloy 5083 in order to remove cutting fluid, Journal of Cleaner Production. 68 (2014).

DOI: 10.1016/j.jclepro.2013.12.056

[13] Gerth, Julia, et al, On the wear of PVD-coated HSS hobs in dry gear cutting, Wear. 266.3 (2009) 444-452.

DOI: 10.1016/j.wear.2008.04.014

[14] Rech, Joël, Influence of cutting edge preparation on the wear resistance in high speed dry gear hobbing, Wear. 261.5 (2006) 505-512.

DOI: 10.1016/j.wear.2005.12.007

[15] Klocke, Fritz, Christof Gorgels, and Stefan Herzhoff, Tool load during multi-flank chip formation, Advanced Materials Research. 223 (211) 525-534.

DOI: 10.4028/www.scientific.net/amr.223.525

[16] Klocke, Fritz, Markus Brumm, and Stefan Herzhoff, Influence of gear design on tool load in bevel gear cutting, Procedia CIRP. 1 (2012) 66-71.

DOI: 10.1016/j.procir.2012.04.010

[17] Bouzakis, et al, Determination of chip geometry and cutting forces in gear hobbing by a FEM-based simulation of the cutting process, Proceedings of the 8th CIRP International Workshop on Modeling of Machining Operations, Chemnitz. (2005) 49-58.

[18] Bouzakis, et al, Manufacturing of cylindrical gears by generating cutting processes: A critical synthesis of analysis methods, CIRP Annals-Manufacturing Technology. 57.2 (2008) 676-696.

DOI: 10.1016/j.cirp.2008.09.001

[19] G.A. Harlanov, A.S. Tarapanov, The design of cutting processing, Mechanical engineering, Moscow, (2003).

[20] Johnson, R. Gordon, and W. H. Cook, Fracture characteristics of three metals subjected to various strains, strain rates, temperatures and pressures, Engineering fracture mechanics. 21.1 (1985) 31-48.

DOI: 10.1016/0013-7944(85)90052-9