Search results

On the relation between the matensite start stress and the temperature in single crystalline Cu-11.5wt%Al-5.0wt%Ni shape memory alloy T.Y.
Beke c, Department of Solid State Physics, University of Debrecen, PO Box. 2, H-4010 Debrecen, Hungary a tarekyousif75@yahoo.com, bldaroczi@tigris.unideb.hu, cdbeke@delfin.unideb.hu Keywords: shape memory, Clausius-Clapeyron relation, transformation temperatures and stresses, Cu-11.5w%Al-5.0wt%Ni alloy Abstract.
Analysis of experimental data First of all let us see the ε tr (σ) and ε tr (T) functions, obtained from ε ~T and ε ~σ hysteretic loops measured at constant stress and temperature values, respectively in Cu-11.5wt%Al-5.0wt%Ni shape memory alloy [2].
El Rasasi, L.
El Rasasi, L.

Zein El Abedin, F.
El Abedin, N.
El Abedin, F.
El Abedin, F.
El Abedin, F.

Compared with Huang et al.’s scheme, the signature size is shortened about 25% and the computation quantity is reduced about 36% in the proposed scheme.
Efficiency We give a comparison between the proposed scheme and Huang et al.’s scheme [13].
Mu et al..
El Aimani, On generic constructions of designated confirmer signatures.
El Aimani, Toward a generic construction of convertible undeniable signatures from pairing-based signatures, Cryptology ePrint Archive, Report 2009/362, 2009, http://eprint.iacr.org/

Higher Heating Value (HHV) and Lower Heating Value (LHV) of wet pomace HHV, Kcal/Kg LHV, Kcal/Kg Wet Pomace 4512.00 + 38,45 4107.73 + 38,45 a), b), c), and d) Q=Quatz Do=Dolomite Ca=Calcite Ve=Vermiculite Al=Albite Bi= Biotite Bi Q Q Al Ca Do Q Ca Ca Do Bi Bi Q Bi Q Bi Bi Q Do Al Al Q Q Q Q Q Al Bi Ve Ve Bi Q Q Q Al Ca Al Do Ca Q Ca Al Ca Ca Q Q Do a) b) c) Figure 1.
Supported by Consejería de Economía, Ciencia y Empleo de la Junta de Andalucía and el Ministerio de Economía y Competitividad.
http://www.magrama.gob.es/es/estadistica/temas/novedades/Olivar2012_tcm7-262578.pdf [4] Elaboración del aceite de oliva de calidad obtenido por el sistema de tres fases 1996 (CAPYA Junta de Andalucia, 27)
El-Maghraby (2002).

Ghougali Mabrouk for his assistance in XRD data acquisition from, University of El-Oued, Algeria.
Baik, et al., Effect of fluorine addition on transparent and conducting Al doped ZnO films, J.
Cheong, et al., Electrical, optical and structural properties of transparent and conducting ZnO thin films doped with Al and F by rf magnetron sputter, J.
El Ghoul, M.
El Mir, Synthesis of co-doped ZnO nanoparticles by sol–gel method and its characterization, J.

Aluminum (Al) alloys are the most widely used in the high strength to weight ratio.
Thamizhmanii et al [6] discussed the effect of burnishing parameters on surface finish and surface hardness.
Al composite also got a little attention as a material can be finished by burnishing.
El-Khabeery, M.H.
El-Axir, “Experimental techniques for studying the effects of milling roller-burnishing parameters on surface integrity”, International Journal of Machine Tools & Manufacture, 41 (2001), pp 1705–1719

El Rayes1,a *, Ehab A.
El-Danaf 2,b and Abdulhakim A.
Di Gianfrancesco et al. [1] summarized the microstructural evolution of 9-12% Cr steels.
Armaki et al. [3] studied the microstructural degradation mechanisms during creep in high Cr ferritic steels.
(wt. %) C: 7.93; Cr: 20.33; Fe:70.91; Al: 0.82 a) (wt. %) C: 9.52; Cr: 39.84; Fe: 50.64 b) Fig. 5.

The test specimens, Al-6Si-2Cu alloys are prepared by gravity casting process.
The high-strength Al alloy Al-Si-Cu system is widely used in cylinder head, cylinder block, etc. due to excellent castability and mechanical properties[1].
The process of heat treatments on Al cast alloy is listed in Table 2.
Chemical composition of Al-Si-Cu alloy (wt.%).
Alloy Si Cu Fe Mn Mg Al Al-Si-Cu 6.01 2.09 1.03 0.19 0.12 Bal.

The latter is a new and very challenging idea presented by Schmidt et. al. [2].
al. for FRFs and so called Ritz-vectors, see [46].
Each element "el" is tested; ))(),(( 0 0 , xxf EI EI i d id el el iel ϕϕ β ''''== . (13) The underlying model is an Euler-Bernoulli flexible beam.
Lallement et.al. [31] and He et.al. [32] have pointed out that the zeros (or antiresonances, where Hik(ΩAR) = 0) introduce useful additional information about a dynamic system.
Sohn et.al. [16] demonstrated the use of the Auto-Regressive (AR) and AR with Exogenous input (ARX) models.

The alloys are AA2024-T3 (Al-Cu) and AA2099-T8E77 (Al-Cu-Li).
Ma et al [5] examined an AA2099 alloy and found that rod like Al-Cu-Mn-Li dispersoids (~1 µm x 200 nm) and spherical Al3Zr dispersoids (25-30 nm diameter) were present.
Analysis of the precipitates present within the matrix, showed that those in alloy 1 were rich in Al-Cu-Mg-Fe-Mn but Al-Mg-Mn-Si particles were also observed.
El-Houd, and F.
El-Shawesh, “A study on the corrosion behavior of Aluminum Alloys in seawater,” Mater.