Search results

The present study therefore, is aimed at examining the effects of magnesium on the dielectric constant of CaTiO3.
Moderate to high Mg doping however has been reported to contribute to grain refinement which has been attributed to the dopants or compounds formed that diffuse to the grain boundary area and act as pinning agents that thus inhibit grain boundary mobility.
Jafarian, Synthesis of perovskite CaTiO3 nanopowders with different morphologies by mechanical alloying without heat treatment.
International Journal of Physical Sciences.
Journal of the European Ceramic Society 27. (2007), 1077-1082

The fish fillet usually contains water, salt and other compounds.
As the water in the fish progressively freezes, the concentration of salts and other compounds in the remaining water would increase.
The Fluent software can model the solidification of pure liquid as well as binary alloy solution.
Journal of Food Technology Vol. 21 (1986), p. 209-219
International Journal of Heat and Mass Transfer Vol. 48 (2005), p. 1205-1213.

This approach efficiently explores the temperature dependent thermal boundary condition for a group of friction stir welds of 7449 aluminium alloy.
The aim of the ANN is to find the values of the CSRR, and contact gap conductance parameters, a and b.
Proceedings of 4th International Friction Stir Welding Symposium, 2003(Journal Article)
Colegrove, and J. dos Santos, Hybrid modelling of 7449-T7 aluminium alloy friction stir welded joints.
Suxing Gongcheng Xuebao/Journal of Plasticity Engineering, 2008. 15: p. 284-197.

The aim of experimental design using the Taguchi approach is to select system design parameters that reduce the variation of the system’s performance around the target value, i.e. to obtain near optimum design values while conducting only a limited number of experiments.
Journal of Thermal Spray Technology 2005; 14; 405-413. 3.
Journal of Quality Technology, 12, 214–219. 5.
Journal of Alloys and Compounds 2009;467; 163–167. 10.

These were very good proof-of-principle measurements performed on both steel and aluminum alloys.
It was our proof-of-principle measurement, using a U-shaped 2024 aluminum alloy bar [10, 11].
Fred Smith and Trevor Finlayson, at Monash University, were studying the low temperature thermal expansion of A15 superconducting compounds.
Peter Webster was a physicist at Salford University in the UK using neutron scattering to study Heusler alloys.
The first project was on residual stresses in autofrettaged cylindrical pressure vessels, and the first journal publication was in the Journal of Strain Analysis [23].

And molybdate compounds show many excellent properties in luminescent performance which have come into notice in recent years.
The aim of this paper is to investigate the properties of molybdates with low doping concentration of Eu3+.
Trottier, IEEE Journal of Selected Topics in Quantum Electronics, 8 (2002) 339-345
Alloys Compd. 433 (2007) 352-355
Alloy Compd. 481 (2009) 792-796

Unlike the alloys the composites must be mechanically mixed to achieve the uniform distribution of individual phases while the blending of alloys is based on diffusion processes [1, 2].
The polypropylene obtained from Sumika Polymers Compounds (product name Thermofil PP E020M, without talc) with high melt flow index modified for injection moulding processing was used as a matrix in this study.
The results also denoted that the fibre bundles were split into the individual fibres during the milling, compounding and final processing.
International Journal of Polymer Science [online]. 2011, vol. 2011, p. 1-35 [cit. 2012-05-18].
Rheology, Compounding and Processing of Filled Thermoplastics.

A prospective system of notable interest is the electrodeposition of Mn and Mn-based alloys.
Effects of applied potential and bath temperature on material characteristics of Mn films and Mn alloys electrodeposited in the following systems have been studied: Mn in butylmethylpyrrolidinium bis(trifluoromethylsulfony)imide (BMP-TFSI) [11, 12], Mn in RTILs based on dicyanamide (DCA) anion [17], Zn-Mn alloys in tri-1-butylmethylammonium bis((trifluoromethane)sulfonyl)imide (Bu3MeN-TFSI) [16], Zn-Mn in an eutectic RTIL obtained combining urea-choline chloride in a 2:1 molar ratio [13], Al-Mn alloys in 1-ethyl-3-methylimidazolium chloride, [EMI]Cl [14].
The surface morphologies of Zn-Mn alloys strongly depend on the alloy composition.
This solution was then made 20 mM in each of the following chelating compounds: (i) Titriplex-I: nitrilotriacetic acid (#3 -COOH groups); (ii) EDTA: ethylenediaminetetra-acetic acid: (#4 -COOH groups); (iii) DTPA: diethylenetriamine penta-acetate (#5 -COOH groups).
Sgura: Journal of Physics: Conference Series Vol. 96 (2008), p. 012051 [11] J.

The aim of our study is to deposit good quality (i.e., homogeneous with good adherence) layers at low substrate temperatures. 2.
The observed (hkl) peaks were (110), (101), (200), (211), (220), (310), (112), (301), (202) and (321), indicating that the SnO2 particles in this compound were well-crystallized.
Guo, Optimizing the gas sensing characteristics of Co-doped SnO2 thin film based hydrogen sensor, Journal of Alloys and Compounds, 785 (2019) 819-825
Schmerber, Oxidation temperature dependence of the structural, optical and electrical properties of SnO2 thin films, Journal of Electronic Materials (2016) 4357-4363
Schoonman, Unique porous LiCoO2 thin layers prepared by electrostatic spray deposition, Journal of Material Science, vol. 31 (1996) 5437-5442

The aim is to achieve the annual use of natural ventilation to reduce air conditioning use time and increase the number of ventilators and air quality.
Environmentally friendly building materials developed in the research, development and implementation early , starts to develop some amount of volatile organic compounds distributed test method and provides a number of environmentally friendly building materials, performance standards, and launches a low distribution level mark certification, while develops some new products, environmentally friendly building materials.
Bao: Journal of Henan University(Natural Science), Vol. 34(4), (2004), p.92-95 [3] Q.X.
Zhang: Journal of Xuchang Teachers College, Vol. 21(2), (2002), p.30-33 [7] Q.F.
Ao: Journal of Nanjing University of Technology, Vol. 27(6), (2005)，p.101-106