Search results

It is very well known that hollow particles have low density, high surface area, and distinct optical and mechanical properties [3].
However, the relations among the decomposition of iron acetylacetonate, process variables and powder properties still remain unsolved.
In CVC process, among various process variables affecting formation β-Fe2O3, the reaction temperature is considered as the most important process variable especially controlling phase evolution.
Finally, the properties of iron oxide nanoparticles investigated in this study and in the literature are summarized in Table 1.
The properties of iron oxide nanoparticles investigated in this study and the literature of the author (marked as *). 3. 2.

Interpolation Techniques in Computational Particle Tracking Inside a Direct-Injection Diesel Engine Cylinder Lok Bee Seng1,a, Muhammad AhmarZuber1,b, Wan Mohd Faizal Wan Mahmood1,2,c, Zulkhairi Zainol Abidin1,2,d and Zambri Harun1,2,e 1Department of Mechanical and Materials Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor, Malaysia 2Centre for Automotive Research, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor, Malaysia abichen1989@hotmail.com, bahmarzuber@yahoo.com, cwmfaizal@eng.ukm.my, dzza@eng.ukm.my, ezambri@eng.ukm.my Keywords: Soot, particle tracking, interpolation, trilinear, radial basis function.
Movement of soot particles are examined through the selection factors of particle's initial coordinate (r,Ɵ,z) and soot concentration level at different instant crack angle.
It has been used widely nowadays in automotive field since it has a better fuel efficiency property compared to gasoline engine but it has drawback such as the formation of soot and other pollutants [1].
It happens since interpolation technique computes its result which is affected by the parameter value on the previous time-step where RBF and trilinear interpolation takes on the different value on the related parameter.
By knowing the properties and movement tendency of soot particles, solution to minimize or even control the tendency of soot particles to stick on cylinder wall will have a higher successful probability.

Cox2,m 1Department of Mechanical and Industrial Engineering, University of Brescia, V.
Ti-6Al-4V alloy, which is most used for the fabrication of orthopedic prostheses, is of particular interest for its mechanical properties [5,6].
Factors Levels Values Power 3 50 W 100 W 150 W Scan speed 3 750 mm/s 1125 mm/s 1500 mm/s For each of these nine combinations, three repetitions were performed: in total, therefore, 27 specimens were printed. 3.
Ceretti, “Mechanical characterization and properties of laser-based powder bed–fused lattice structures: a review,” Int.
Birbilis, “Understanding the effects of PBF process parameter interplay on Ti-6Al-4V surface properties,” PLoS One, vol. 14, no. 8, pp. 1–24, 2019, doi: 10.1371/journal.pone.0221198

Landscape Zone Above high water level is landscape zone, of which the hydrodynamic characteristic is affected only by runoff erosions, instead of flows.
Ecological revetment must be fitted into culture and environment in the surroundings, with consideration to anti erosion properties of slope.
Submergence-resistance is not required in the zone, as such, strongly-rooted and inter-crossed herbs, shrubs and trees, which of good mechanical properties, large coverage and some ornamental value, are employed in the zone.
Landscape zone is affected only by runoff erosions, instead of flows.
Combined with ecological characteristics of revetment plants (flood and erosion resistance are fundamental factors), vegetations adapting to different protection area have been analyzed and discussed.

These components endowed COLLOSS® E with all the bone formation activities of osteoconductive, osteoinductive and osteogenic properties.
(b) Most mono-factors are only effective in very high concentrations.
Bioactivity.The ideal bone graft possesses the three properties of osteoconductivity, osteoinductivity, and osteogenicity [1].
Only autologous bone graft is qualified for all the three properties nowadays.
Although many factors have been verified to accelerate bone formation, how these factors do it and interact among them is still mysterious.

Beside the unavoidable poor corrosion properties, magnesium has a poor weldability as well.
Based on the joint properties an adhesive bonding of the parts is preferred.
Beside the thermo mechanical affected zone (TMAZ) borders the heat affected zone (HAZ).
These phases provide, due to their low ductility, an explanation for the lower mechanical properties of the joints.
Department of Materials Science, Osaka Prefecture University; Materials Transactions, Vol. 49 No. 5, 1129 - 1131 - S.(2008) [12] Chang, W. ; Rajesh, S. ; Chun, C. ; Kim, H.: Microstructure and Mechanical Properties of Hybrid Laser-Friction Stir Welding between AA6061-T6 Al Alloy and AZ31 Mg Alloy.

The microstructured-layer in the middle of the model consisted of three phases of unique material properties: the fibre, the matrix and the fibre-matrix interface.
The material properties of the infinite elements were set to be the same as the EHM.
Material Properties and Simulation Conditions.
The material properties used in the FE analysis are given in Table 1 [7, 9, 17], and the cutting conditions are listed in Table 2.
It is clear that the frequency affects the fibre fracture significantly.

The study method and result have great theoretical and practical value for improving the technical management level and the awareness of oil lubrication properties.
The dielectric constant is one important parameter of oil electrochemical properties.
The oil optical property is affected to a great extent by particle contaminant.
Figure 1 two-stage fusion model During signal processing stage, it processes the original data locally and eliminates the interference factor according to the properties of every sensor and sampling object.
China Mechanical Engineering, Vol.18(2007) , p. 1962-1965 (In Chinese) [4] Wang yang Wu and Wei Zhang.

The structure and morphology properties of NiO/CNTs composites are characterized by several techniques.
Measurement of electrochemical properties.
Therefore, the most important factor affecting the coating of NiO is the mass ratio of CNTs versus NiO.
Cyclic voltammetry (CV) is employed to determine the electrochemical properties of the NiO/CNTs electrodes in 2 M KOH.
Yoon, “Pseudocapacitive properties of electrochemically prepared nickel oxides on 3-dimensional carbon nanotube film substrates”, J Power Sources, 182(2008) 642-652

The molecular structure and chemical properties of nitrobenzene are given in Table 1.
This may due the various factors such as morphology, surface area, optical bandgap, and density of the ferrite system.
However, in following section we have tried to explain some of the factors affecting in the photocatalytic activity of the composites.
Modi, Infrared spectroscopy and elastic properties of nanocrystalline Mg-Mn ferrites prepared by co-precipitation technique, J.
Modi, Synthesis of nanostructured material by mechanical milling and study on structural property modifications in Ni0.5Zn0.5Fe2O4,Ceram.