Search results

Vidmanshett structure number 0.5 was observed in the transverse cross section of the rod with 5.5 mm in diameter by optical microscopy analysis (Figure 1, a, b).
Grain number was 8 in accordance with the Russian standard GOST 5639 – 82.

When the premise is guaranteed that simulation hierarchy is consistent, we can perform qualified analysis by simulation experiment on lower level to provide fine-grained verification.
Configuration of Satellite network Orbit type GEO MEO LEO altitude(km) 35786 11946 1000 inclination(°) 0 45 99.6 period(s) 86164.09 24685.75 6307.12 Number of satellites 3 12 4 Number of orbits 1 4 4 Phase factor — 1 — We developed the simulation in two different ways.

The indicated differences in the compositions of impurities (particularly ones crystallized on grain boundaries, in the first place, of lead, antimony and bismuth) allow one to predict a higher scatter of the main indices of copper rod: specific ohmic resistance, a number of rotations before fracture, plastic metal properties, copper density.
Firstly, owing to the ductility reduction the portion number decreased from 6 to 4.

The noted integral models include a number of mathematical models for the quantitative description of the complex evolution of austenite microstructure at the hot rolling stage [7-14], as well as its decomposition during subsequent accelerated cooling with the formation of a set of practically important structural components [15-17].
Composition number Chemical composition, mass. % C Mn Si Cr Ni Mo 1 0.02 1.0 0.5 0.5 0.5 0.5 2 0.08 1.8 − 0.6 0.2 0.2 3 0.09 1.5 0.2 0.8 0.5 − 4 0.10 2.0 0.7 0.3 0.8 1.0 5 0.17 0.74 0.2 − − − 6 0.20 1.5 1.5 − − − 7 0.20 3.0 3.0 − − − 8 0.20 1.0 1.0 1.0 1.0 1.0 9 0.30 − 0.6 1.5 1.5 0.2 10 0.47 1.5 1.5 1.5 1.5 1.5 11 0.50 0.7 0.7 1.0 1.5 0.5 12 0.60 0.9 0.4 0.3 1.2 0.8 The Results and Discussion Formula for A3.
[15] Bradley JR, Aaronson HI (1981) Growth Kinetics of Grain Boundary Ferrite Allotriomorphs in Fe-C-X Alloys.

Then, the single crystal cylinder was withdrawn from the directional solidification furnace with a grain selector.
(2) (3) Where Xi and are the individual and average values for the measured quantities of the specimen, and N is the total number of measurements, respectively [15].
Table 1 Two kinds of etchants for nickel-base single crystal superalloy Etchant number Composition Etching conditions References 1 10ml HNO3-20ml glycerol-30ml HCL Immersion etching at ambient temperature for 30-45s [10] 2 10ml HNO3- 30ml HCL Immersion etching at ambient temperature for 10-15s [10] Results and Discussion Figure 1 shows that the microstructures of γ matrix and γ′ precipitates vary with the etchant solution composition.

The fine aggregate used is broken oil palm clinker which passes through sieve number 5 and below.
Sufficient numbers of oil palm lightweight concrete specimens were casted and tested for compression, flexure, density and modulus of elasticity.
It shows that fine aggregate has higher moisture content due to the fact that smaller grain can hold more water.

These grains are manufactured by heating Carbon under high pressure and high temperature condition in a cubic press device which results in having diamond tables identical to natural diamonds in strength.
Number of elements for PDC cutter assemblies.
Feature Number of Elements Diamond Table Substrate Castle 149536 153209 Dent 131142 141498 Honeycomb 159569 157945 Chase 151748 172514 Boundary conditions and applied velocity.

Number of the experiments is dedicated to groundwater flow and transport of radionuclides along rock fractures.
Glinicki, Application of Image Analysis to Identify Quartz Grains in Heavy Aggregates Susceptible to ASR in Radiation Shielding Concrete, Materials 9(4) (2016), Article number 224

By increasing the number of coefficients, the agreement between the predicted flow stress and the experimental one gets worse, causing a decrease in the R2 from a value of 0.972 for the H-S law with 5 coefficients to a value of 0.939 for the H-S law with 9 coefficients, as shown in Fig. 7 and Fig. 8.
Funding National Recovery and Resilience Plan (NRRP), Mission 04 Component 2 Investment 1.5-NextGenerationEU, Call for tender n.3277 dated 30/12/2021 (Award Number: 0001052 dated 23/06/2022).
Tomesani, Grain evolution analysis and experimental validation in the extrusion of 6XXX alloys by use of a lagrangian FE code, International Journal of Plasticity 46 (2013) 70-81

Its configurations are described by the occupation number sets {nqi} where q is p or v; nqi is 1 when site i is occupied by an atom q and zero otherwise; and ∑ q nqi ≡ 1.
Thus, in the last term of SKE (6), the full fluctuative transfer δn f ij should be replaced by its long-wave (or ``coarse-grained'') part δn fc ij .
This maximum thermodynamic gain should evidently correspond to formation of the maximum number of large supercritical precipitates.
Average number of copper atoms within a precipitate versus the evolution time t (in seconds).
Left: Evolution of total number of supercritical precipitates within simulation box.