Search results

Negative stiffness device Fig. 1.
At point-“1” in Fig. 1(a) the secant stiffness() and tangential stiffness (slope at point-“1”) are both negative.
Table 1.
References [1] Constantinou, M.
Earthquake Engineering and Engineering Vibration, 8(4), 469–479

This is different from the conventional method, in which APS is only as the oxidant and the polymerization is carried out in a strong acidic medium (e.g.1.0M HCl)[1].
In this study, all polymerization was carried out at a constant molar ratio of monomer to APS (e.g. 1:1).
Table 1.
References [1] A.
Heeger, Flexible light-emitting diodes made from soluble conducting polymers, Nature 357 (1992) 477-479

Fig. 1 also showed spectrums of the purified products after the SMB separation.
The HPLC spectrum of the feed is also illustrated in Fig. 1.
The Separation by SMB Spectrums of the extract and the raffinate for Runs 1~4 are illustrated in Fig. 9a~d.
Reference: [1] B.B.
Eng. 5(6) (2011) 479-786

Fig.1 Material flow analysis indicators of national circular economy To evaluate the recycle degree of the resource materials, it is necessary to define evaluation indexes below: 1) Material Productivity (MP).
Table 1 shows the calculated life distribution data of different sectors.
References [1] Dajian, Z., Sustainable development calls for recycling economy, Technol.
Recy. 1 (2007) 118-140
[10] China Iron & Steel Association, China's Steel Demand Forecast for 2005 and 2010, China Steel 1 (2003) 12-16.

Surfactant Sodium Dodecyl sulphate (SDS or NaDS) or sodium laurel sulfate or sodium lauryl sulfate (SLS) is an organic compound with the formula CH3(CH2)11OSO3Na, Molar mass of 288.372 g/mol, Density of 1.01 g/cm³, Melting point 206 °C, 479 K, 403 °F, Refractive index (nD) 1.461.
Figure 1, shows the experimental set up.
The cores were flooded with 1.5PV of brine to experience a water cut of about 90%.
Sw*=sw-swc/(1-sw) (1) Krw=√Sw*Sw3 (2) Kro=1-Sw*[1-Sw*0.25sw]½ (3) It can be noted from the relative permeability curves that the nonwetting phase (oil) loses its mobility at higher values of water saturation.
Advances in Petroleum Exploration and Development Vol. 2, No. 1, (2011), pp. 13-18 [26].

Fig. 1.
China Food Additives, vol. 2, pp. 1-7, 1999
Immunol Res., vol. 21, pp. 1–6, 2000
Microbiol Immunol., vol. 44, pp. 473–479, 2000
Fish Res., vol. 7, pp. 1-9, 1989

The Finite element simulation results of both coated and uncoated valves are presented and analyzed in this paper. 1.
Based on the SEM of the failed engine valves and new engine valves, the following observations were made; 1.
The results that were observed in the chemical (EDS) analysis images of failed engine valves and new engine valves are 1.
The coatings are represented on the abscissa from 1 to 9, which are Uncoated SUH11 valve (1), Coated TiC (2), Coated TiN (3), Coated TiCN (4), Coated TiAlN (5), Coated TiC/Al2O3(6), Coated TiN/Al2O3(7), DLC(8) coating respectively.
References [1] S.P., Herman, R, and Buuck, B (2006) Stress Analysis of an Automotive Pang, M.

Table 1.
Fig. 1 Flow chart for mix design.
Type 1 was 6.5% Sika Latex and 0.45 water-to-cement ratio.
The mixture followed Viet Nam standard TCVN 13567-1:2022 [32].
[32] TCVN 13567-1:2022,"Hot mix Asphalt pavement layer-Construction and Acceptance: Part 1-Dense-Graded asphalt concrete".

Due to the high radioactivity of Pu, Ce was used as a surrogate of Pu for the researches because of their physico-chemical similarity[1].
Then the microspheres were kept in a mixture of ammonia solution and water with the volume ratio of 1:1 to complete the gelation process.
Fig. 6(a-d)1 and Fig. 6(a-d)3 are the surface morphology of CeO2 beads, while Fig. 6(a-d)2 and Fig. 6(a-d)4 are the cross section morphology.
References [1] M.
Lee, Photocatalytic effect of the sol-gel derived nanoporous TiO2 transparent thin films, Thin Solid Films. 479 (2005) 310-315

Localized plasmon resonances in gold and silver microcones fabricated using single-pulse femtosecond nanoprocessing Kuchmizhak A.A.1,2,a, Vitrik O.B.1,2,b and Kulchin Yu.N.2,c 1 School of Natural Sciences, Far Eastern Federal University, 8 Sukhanova str., Vladivostok 690041, Russia 2Institute of Automation and Control Processes, Far Eastern Branch, Russian Academy of Science, 5 Radio str., Vladivostok 690041, Russia aalex.iacp.dvo@mail.ru boleg_vitrik@mail.ru ckulchin@dvo.ru Keywords: Localized plasmon resonances, nanostructures, laser material processing, microcones, noble metal films, photoluminescence enhancement.
Fig.1.
Figures 1(i-l) demonstrate the series of AFM images of the same microcones previously depicted in Fig. 1(a-d).
References and notes [1] J.A.
A, 106 (2012) 479-487