Search results

Al-Degs, M.I.
El-Barghouthi, A.H.
El-Sheikh, G.M.
El-Sakhawy, Carboxymethyl cellulose-g-poly (2-(dimethylamino) ethyl methacrylate) hydrogel as adsorbent for dye removal, Int.

Ibrahim1,3,b 1Environmental Engineering Department, Egypt-Japan University of Science and Technology (E-JUST), New Borg El Arab City, Alexandria 21934, Egypt 2Department of Public Works Engineering, Faculty of Engineering, Mansoura University, Mansoura 35516, Egypt 3Environmental Health Department, High Institute of Public Health, Alexandria University, Alexandria 21544, Egypt amahmoud.samy@ejust.edu.eg, bmona.gamal@ejust.edu.eg Keywords: Degradation rates; Iron waste; Methylene blue; Operating parameters; Real wastewaters Abstract.
Su et al. (2019) found that pH values of 4 and 6.5 were favorable for the degradation of orange II using α-FeOOH@GCA in the presence of persulfate ions [19].
El-Etriby, Synthesized nano titanium for methylene blue removal under various operational conditions, Desalin.
El-Etriby, D.C.

Al-Saadi1,b* 1Department of Civil Engineering, University of Baghdad, Baghdad, Iraq adr.bushra_albusoda@coeng.uobaghdad.com, bsaadysemaa@gmail.com Keywords: Geogrid, soil model, interface, modeling, numerical analysis.
Abo El-Soud, Numerical modeling of geogrid reinforced soil bed under strip footings using finite element analysis, 18thInternational Conference on Civil and Construction Engineering, Jeddah, Saudi Arabia, Volume 10 (2016)

Proposal of compact optical system using planar lightwave circuit for precision measurement based on levitation mass method Koichi Maru1,a and Yusaku Fujii1,b 1Department of Electronic Engineering, Gunma University, Kiryu Gunma 376-8515, Japan amaru@el.gunma-u.ac.jp, bfujii@el.gunma-u.ac.jp Keywords: Planar lightwave circuit; Levitation Mass Method; precision measurement Abstract.
On the other hand, Fujii et al. have proposed a method based on the law of conservation of momentum, in which an impulse is generated and directly transferred to the transducer being tested [2,3].

In order to determine yield point (YP), ultimate tensile strength (UTS) and total elongation (El) tensile test experiments were performed.
STEM micrograph of water atomized material W: (a) extruded at 375°C (white arrows are markers for iron inclusions), (b) extruded at 325°C with element mapping (O, Al, Mg) of magnified area.
Extrusion temp. 375°C 325°C C W A N W A N YS [MPa] 75 76 105 63 106 129 143 UTS [MPA] 103 103 140 153 120 154 168 El [%] 36 37 24 22 11.1 8.3 6.7 HV 31 30.1 37.9 44.5 36.2 46 49.9 HV Std.

Heat input, El ** [KJ/mm] 2.87 2.30 2.67 2.75 1.02 7.
El=kUIvs x 10-3 (kJ/mm), (2) k - Thermal efficiency, dimensionless, I - Welding amperage, (A), U - Welding arc voltage, (V), vs - Welding speed, (mm/s).
Table 4 Chemical composition of the stainless steel and the welded seam Joint Area Chemical elements [%], determined as the average of 5 measurements   Fe C Si Mn P S Cr Mo NI Al Co Cu Nb Ti V W Pb Sn B Ca Zr As other elements X2CrNiMo17-12-2 68.98 0.0246 0.3466 1.74 0.0139 0.005 16.54 1.798 9.878 0.0111 0.0974 0.2692 0.0085 0.0033 0.0834 0.0589 0 0 0 0 0 0 0.1669 Welded seam 63.02 0.0535 0.6524 0.732 0.0146 0.0105 22.18 0.2514 12.6 0.0116 0.0713 0.0775 0.0219 0.0450 0.0704 0.02 0 0 0 0 0 0 0.1674 Nie= Ni+30C+0,5Mn (3) Cre= Cr+1,4Mo+1,5Si+0,5Nb (4) Values obtained: ü for X2CrNiMo17-12-2 : Nie=11.25%; Cre=20.25% ü for the welded seam : Nie=14.57%; Cre=23.42% Using the formulas above and the Schaeffler diagram for determining the weld microstructure, of the austenitic stainless steel and the welded seam, resulted that the amount of ferrite presented in the metal is between 10% and 20%.

El Hage then used a differential equation to describe the profile of cornea along a meridian[6].
[4] Halstead M A, Barsky B A, Klein S A, et al.
[6] El Hage S G.

El-Naggar, H.C.
El-Naggar, L.C.
Behrooz, e-Polymers 104 (2009) ISSN 1618-7229 [19] Al-Ah.

University Avenue, University of Texas at El Paso, El Paso 79968, USA ajiangyueneu@163.com, bzhdwang@mail.neu.edu.cn, cdengxiangtao123@163.com Keywords: rare earth element Ce, mechanical properties, high-angle grain boundaries, inclusions.
C. et al. (2017) 'Influence of rare earth elements on microstructure and mechanical properties of high speed steel', Powder Metallurgy Technology, [2] Sun, M.

ABD EL HALEEM, BADR G.
El-Tantawy, F.
Al-Kharafi, A.