Search results

El. 32 (2021) 10820-10834
El. 31 (2020) 11833-11846
El-Agawany, K.A.
El-Mallawany, E.
Spessato, A.L.

Hampshire et. al. [9] also reported this behaviour in their work.
El-Amir, D.
El-Anadouli, Synthesis of nanocrystalline MgO/MgAl2O4 spinel powders from industrial wastes, Journal of Alloys and Compounds 691, 2017, pp 822-833, DOI: 10.1016/j.jallcom.2016.08.279 [12] W.

Mohtadi-Bonab et al. [28-29] investigated the various factors affecting fatigue crack growth in pipeline steels.
On the other hand, tensile tests showed anisotropic behavior for Yield Strength (YS) and elongation (%EL) properties.
Figure 4 shows YS and %EL values, reported in literature for low strength API 5L steels, similar to the one used in this experimentation.
In addition, from the fatigue data reported by Hong et al. [41], the B exponent was estimated for comparison purposes.
[43] El‐Danaf E., Baig M, Almajida A., Alshalfan W., Al‐Mojil M, Al‐Shahrani S.

Park, et al.
[7] N Linh-Trung, A Belouchrani, Abed-Meraimet K, et al.
[8] A Aissa-El-Bey, N Linh-Trung, Abed-Meraimet K, et al.
[10]S Arberet, A Ozerov, R Gribonval, et al.

S .Torii, S .Yoshizawa et al [4] had studied the superconductor and mechanical properties of Bi-2223/Ag-wires and found that the Ag wires in the Bi-2223 not only stabilize the superconductivity of the bulk , but also reinforce the mechanical characteristics.
Coto et al.: Jpn.
Muller et al.: Physica C, Vol. 153 (1998), p. 1574 [4] S.
El-Tantawy and R.
Zeimetz et al, Eur.

Tsukatani et al. [1] reported that plastic anisotropy of annealed Ti bearing IF steel sheet depend on initial microstructure of hot rolled sheets.
Senuma et al. [2] studied influence of cooling condition after hot rolling on grain refinement for ELC steel.
Abe et al. [3] well established the relationship between initial microstructure and final formability.
%Al, 0.1wt.
pattern Average ferrite grain size(µm) ∆r R-bar YS TS T-El Hot rolled sheet Annealed sheet  16.7 7.1 0.60 1.36 236 351 40.7 ‚ 20.8 7.7 0.67 1.33 242 353 40.8 Summary We have studied the influence of initial microstructure on formability and final microstructure for Cu-bearing ELC steel sheets.

With 15% of GP, Rahma et al. and Kalakada et al. [14,15] found a slump reduction of 35% and 33%, respectively.
Accordingly, Olofinnade et al. [10] found a maximum loss of 30% with 30% GP replacement.
In the case of air content, Schwarz et al. [16] found a 0.5% decrease with 10% GP replacement and Zidol et al. [17] registered a variation no greater than 1% with 20% and 30% GP substitution.
García Del Toro et al. [18] studied the air content in 3 mixtures with 15%, 30% and 45% of GP with a w/b = 0.55.
Raffo, Conoce el proceso de reciclaje de la planta más grande del Perú, (2020)

., et al., Posterior jaw bone resorption in osseointegrated implant-supported overdentures.
Abd El-Dayem, and M.
[12] Li, W., et al., Fibre reinforced composite dental bridge.
[18] Lin, D., et al., Mandibular bone remodeling induced by dental implant.
[19] Chen, J., et al., Multiscale design of surface morphological gradient for osseointegration.

Umeda et al.
Bazaz et al.
Chattopadhyay et al.
El-Betar et al.
Bera et al.

The asymmetric stretching vibrations of the internal tetrahedral Si-O and Al-O groups in CFA are shown at a wavenumber of 1095 cm-1.
Wide absorption at a wavenumber of 3425 cm-1 indicates the presence of O-H stretching vibrations in Si-OH, Al-OH, and water molecules that are absorbed by CFA.
Al Bari, Perbandingan Regulasi Fly Ash sebagai Limbah B3 di Indonesia dan Beberapa Negara, Media Komun.
El Alouani, S.
El Achouri, M.