Search results

Materials and methods Experiment apparatus and materials Self-made dynamic experimental apparatus, U.S. orion5-Star conductivity/pH/ORP analyzer, 721 Spectrophotometer, pH/Cond 340i Oxidation reduction potentiometer, stainless steel tube et al.
Water quality parameter analytical method: reference to “the water and wastewater monitoring and analysis methods” (fourth edition) [10]. 1-inlet temperature monitor; 2-electric heater; 3-wall temperature monitor; 4-data acquisition card; 5-industrial computer; 6-water bath temperature monitor; 7-constant temperature water bath; 8-heat exchanger tube; 9-outlet temperature monitor; 10-upper tank; 11-heat exchanger; 12-lower tank; 13-cooling water circulation pump; 14-upper tank temperature monitor; 15-air circulating pump; 16-air-cooled tank; 17-air-cooled radiator; 18-air-cooled motor; 19-inverter; 20-PID controller Fig.1 Schematic diagram of dynamic simulation system for forming fouling Conclusion and discussion Impact of water quality on biofouling formation For studying the water quality parameters on the influence of fouling formation, the paper did online or offline detection about water quality parameters with the growth of SRB and IB, the formation of biofouling.

However, very few data actually provides insights regarding the influence of the tree species on the spatial variability of soil respiration in subtropical coastal forests.
However, McCarthy and Brown [12] showed that soil respiration did not significantly differ with reduction in canopy cover, even though soil temperature and moisture were significantly different in stands with 60% and 100% canopy cover.

In spite of reductions in fertilizer use, loss of nitrogen and phosphorous from the farmers’ fields together with, e.g., faecal contaminants and pesticides impose a threat to surface and ground water, and in the end to the world consumer.
A basic data set of physical and chemical properties of the soils at the experimental sites should be collected before the experimental starts.

It can be seen as the included angle increases, the inclined support shared the load reduction.
Comparing the results in table 2 with Plan 5 data in table 1, we can see the difference is small, that means horizontal moving force have little influence on load distribution effect of multi support underpinning structure.

Specification data of compressor Boyard HB075Z12 DC 12 Specification Rating Model HB075Z12 Dispalcement 7.50cm3 Weight(Oil include) 6.5 kg Cooling Capacity 850W Power input 340W Current 26.2A COP 2.5 Ambient Temp -7~43oC Evaporating Temp -15~15oC Condensing Temp 45-65oC Compression ratio 7 Compressor Temperature controller Hot air Cooling air Figure 6.
Reduction in Vehicle Temperatures and Fuel Use from Cabin Ventilation, Solar-Reflective Paint and a New Solar-Reflective Glazing, SAE World Congress, Detroit, Michigan, April 16-19, 2007

Moreover, since only meshing of the grain boundaries is required, simplification in data preparation and reduction in the number of DoFs are attained, with consequential computational benefits.

Pressure difference was monitored throughout the experiment using a pressure sensor which was connected to the data logger.
Retention of nanoparticles in the porous media will cause permeability reduction due to the incompatibility of the dimension of pore throat and agglomerated nanoparticles.

The technology of producing recycled cermet powder included the following steps: 1) preliminary mechanical treatment for size reduction of worn inserts in a centrifugal-type pre-crusher DSL-350; 2) intermediate milling in a disintegrator DSL-115 to provide particle size less than 200 µm; 3) final milling into 1–45 μm particles in the laboratory disintegrator milling system DSL-175 in separative milling conditions. 4) Sieving the obtained powder to the required particles size.
Table 1 provides the data for the separation of powders after 3D printing.

Photogenerated electrons are rapidly transported to the Gr surface and play a significant role in the reduction.
According to the data above, a significant improvement of electrochemical performance was observed for Gr-ZnO nanocomposite compared with pure ZnO; the addition of Gr can provide a fast redox reaction and form the open structure allowing rapid and effective ion charge transfer and electron transport.

Each data point represents the average value of six measurements.
Because the reduction of the tensile strength due to calcium-chloride is caused only by 1.7 % w/w, whereas the degradation due to H2O is effected by 6 % w/w change in mass.