Search results

This apparently suggests urgent needs for further reduction of waste generation and development of waste recycling.
Another requirement for the planning approval was relaying real time emissions data (NOx, SOx) to local government offices.
Emissions data are also constantly displayed on the operation consoles of the plant and monitors in a reception room for visitors and local residents as reference.

Linear least squares regression was then applied to the absorbance data as expressed by equation 1.
Results Table 1 lists the B12 concentration versus time data for each dialyzer and concentration reached at equilibrium before and after antibody were added to the system.
Since the system had come into equilibrium before the anti-B12 antibodies were introduced, the Ksink term represents “restored” clearance due to an immediate reduction in the concentration of free or “unbound” B12.

Most of the models utilised only the initial and final textures with no other independent data and usually the austenite parent texture has had to be assumed.
In this thick plate, the micro-segregation pattern is not extremely lamellar since the total reduction from the as-cast state is less than 80%.
Sections of the ODFs are presented in Fig.5 for the parent austenite textures and the transformed ferrite textures with and without variant selection The present results make assumptions about the degree of activation of variant selection that cannot be tested on available data so they are only qualitative in predicting the type of texture change that is to be expected.

This size reduction process aimed to expand the contact surface between OPEFB and active agent in pretreatment process.
Based on simulation performed by SuperPro Designer v9.5 using all technical data parameter mentioned in Methods, production of rhamnolipid using solvent extraction purification methods required more OPEFB feedstock to produce the targeted production capacity than using adsorption chromatography.
In this study, calculation of profitability performed by SuperPro Designer v9.5 using economic data which accordance to planned design process simulation.

It is clear from the CA data that using nanoclay led to enhance ng the surface hydrophobicity of PLA film to a value of 14.7°.
Data pertaining to CA marked that the irradiation of 40 kGy increased the CA value to become (θ=58.4°).
In another part it is ascribed to the number of crystallites in terms of reduction surfaces under the melting peaks and the narrowing crystalline size distribution.

The purpose was to test whether the data collected by strain gauges and displacement meters were accurate and effective, and to make the specimen in good contact with the loading device, and then entered the formal loading stage.
The data in the test process were collected automatically by the instrument.
According to code DL/T 5085-1999, the predicted ultimate bearing capacity of CFST with DCLs column can be expressed as follows: (15) (16) (17) Where ,is the area of steel and concrete; is the yield strength of steel; is the cylinder strength of the concrete; is bearing capacity reduction factor considering slenderness ratio; is hoop Coefficient of Concrete Filled Steel Tubular; is limit value of hoop coefficient relating to concrete strength grade.

The data of stability and flow was recorded for each of the specimens.
The test sequence comprised of 150 conditioning pulses followed by 5 data acquisition pulses.
Reduction of plastic deformation in heavy traffic intersections in urban areas.

The purpose of the notification, investigation and analysis of accidents and incidents is to adopt the necessary measures to prevent their repetition by obtaining objective data that allow the facts to be defined and the basic causes that originated them to be established.
Dive data: Depth/Time at the bottom/Decompression 11.
Operational control, establishing specific methodologies and programs for the reduction and control of risks derived from underwater activities.

Fig.4 Arrangement of DWVG on absorber plate in solar air dryer. 2.1 Experimental data reduction Different studied parameters such as wall temperature, inlet and outlet air temperature, thermal efficiency, and useful energy were conducted in this experiment as described in the following: The mass flow rate value is gained by: 𝑚̇ = 𝜌𝑎 .𝑉𝑚.
The collected data reveals that for certain DWVG parameter values, a similar trend in thermal efficiency variation is gotten with different hourly solar irradiance in December.

The objectives of this study are (i) to conduct an experimental study analysis of electrocoagulation flocs from peat water sources at varied currents and reaction time by using batch electrocoagulation treatment with aluminium electrodes, (ii) to study on the composition and structure of electrocoagulation flocs by using Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX), and (iii) to conduct an operating energy cost analysis of peat water batch electrocoagulation treatment. 2.0 Methodology The methodology of the research consists of several parts: (i) study locations, (ii) experimental study, (iii) flocs analysis, (iv) water quality analysis, (v) data analysis and (vi) economic analysis. 2.1 Study Locations.
Water conductivity and salinity are measured by a conductivity meter, Hanzhan EZ-9910. 2.4 Data Analysis.
The dissolution of coagulant into solution is governed by Faraday’s Law as shown in Eq. 6: (6) where w is the metal dissolving (g M/cm2), I is the current (A), t is the time (t), M is the molecular weight of metal (gr/mol), Z is the number of electrons involved in the oxidation or reduction reaction and F is the Faraday’s constant (96,485 C/mol).