Search results

Because of their brittle material and complicated structure, the force and the deformation of assembly must be considered.
Acknowledgements This work was financially supported by the National Natural Science Foundation of China (grant no. 51127004 and 1105036).
Any opinions, findings and conclusions or recommendations expressed in this material are those of the authors and do not necessarily reflect the views of the National Natural Science Foundation of China.
,et al: ‘Lessons from Building Fusion Ignition Targets with the Precision Robotic Assembly Machine’, Fusion Science and Technology, Vol. 59,pp.70-77(2011)
[5] Zhao Hui, Yu Pu,et al: ‘ Research of Automatic Measurement Method of Stiffness of Small Size FlexibleParts’, Chinese Journal of Scientific Instrument: vol 22, June,49-50(2001)

The density, thermal conductivity, heat capacity, heat transfer coefficient and the initial temperature of materials should be set up before using transient heat transfer simulation by ANSYS.
Li: Journal of Plasticity Engineering.
Nye: Journal of Materials Processing Technology.
Liu: Numerical Simulation of Heat Treatment (Science Press, Beijing1996) [5] Q.X.
Chang: Heat Transfer Theory (Science Press, Beijing2009) [9] Z.Q.

Such materials as rock and concrete is much lower in tensile strength than in compressive strength and they are broken easily by tensile stress, it is therefore more important to understand the tensile strength reduction of concrete induced by microwave irradiation.
The author expresses his gratitude to the committee of the national natural science foundation of China for the support.
Journal of Building Structures, 1993, 14(1): 8~16 [2] Xie Dimin, Jin Xianyu.
Journal of Zhejiang University, 1998, 32(5): 597~602 [3] Li Wencheng, Du Xuepeng.
Construction and Building Materials, 25: 3469~3479 [9] Yang Shengquan, Yang Junsheng.

The liner material was copper; STEINBERG and GRUNEIDEN were adopted.
The parameters of each material are to be found in Table 1.
[3] Gou Ruijun, Zhao Guozhi, Du Zhonghua, The power research of LEFP. explosive materials 2005;34 (5) : 25 -28
[4] Du Zhonghua, Duan Weiyi, The simulation research on formation and penetration in different ways of initiation for LEFP. journal of Nanjing university of science and technology 2009; 33(6) : 756-759
International Journal of Impact Engineering. 2010;37;414-424

The Preparation of PVAc with Lower PDI through RATRP in Miniemulsion Polymerization Haike Feng1,2,a, Yi Dan2,b 1College of Material, Chemistry and Chemical Engineering, Hangzhou Normal University, Hangzhou, 310036, China 2State Key Laboratory of Polymer Materials Engineering of China,Polymer Research Institute of Sichuan University, Chengdu 610065, China a fhkfhk@163.com, bdanyichenweiwei@163.com Keywords: reverse atom transfer radical polymerization, molecular weight distribution, polyvinyl acetate, miniemulsion polymerization Abstract.In this paper, reverse atom transfer radical polymerization (RATRP) was used to prepare polyvinyl acetate (PVAc) with lower polydispersity index (PDI).
Experimental Materials Vinyl acetate (analytic reagent grade, A.R) used after distilled was obtained from Chengdu Kelong Chemical Reagent Factory (Chengdu City, China).
Acknowledgement The authors are grateful to the National Natural Science Foundation of China (NO.20374036) for support of this research.
:Carter:Journal of the American Chemical Science Vol.125 (2003), p.3831-3838
Dan:Journal of Applied Polymer Science, Vol.99 (2006), p.1093-1099.

The new materials can solve the problems that architectural absorbing materials are large density and narrow absorbing frequency effectively.
[5] W.J.Hao: Science and technology of foreign building materials Vol.25 (2004),p.74-76(In Chinese)
Guo: Journal of Functional Polymers Vol.24 (2011), p.353-358 (In Chinese)
Yang: Journal of Functional Polymers Vol.25 (2012), p.393-396 (In Chinese)
Zhu: Materials Review Vol.24 (2010),p. 9-11(In Chinese).

Resistive switching behavior in undoped α-Fe2O3 film with a low resistivity Yukiko Ogawaa *, Yuji Sutoub, Daisuke Andoc and Junichi Koiked Department of Materials science, Tohoku University, Sendai 980-8579, Japan ab4td5301@s.tohoku.ac.jp, bysutou@material.tohoku.ac.jp, cdando@material.tohoku.ac.jp, dkoikej@material.tohoku.ac.jp Keywords: iron oxide, resistive switching behavior, Schottky contact Abstract The resistive switching behavior of a low resistive p-type α-Fe2O3 thin film sandwiched between Fe bottom electrode and top electrodes of various materials (Fe, Ni and TiN) was studied by current-voltage measurements.
Introduction Oxide materials have been reported to show resistance change by applying voltage and attracting considerable attention for use as resistive random access memory (ReRAM).
In the present study, the effect of top electrode materials on the resistive switching behavior of the p-type α-Fe2O3 film was investigated.
Conclusion In this study, the resistive switching behavior of a low resistive p-type α-Fe2O3 thin film sandwiched between Fe bottom electrode and top electrodes of various materials (Fe, Ni and TiN) was investigated.
Bulhões, Journal of Electroanalytical Chemistry, 452 (1998) 229-234

However, in vitro apatite-forming ability alone does not always adequately assure the material-bone bonding in vivo.
Osaka : Key Engineering Materials, Vol. 240-242(2003), p.55 [2] E.
Gaul : Journal of Chemical Education, Vol. 70(1993), p176 [3] X-X.
Osaka : Key Engineering Materials, Vol. 309-311(2006), p.717 [5] JM.
Osaka : Key Engineering Materials, Vol. 309-311(2006), p.407

Besides, in real production, manufacturing systems tend to be prone to unpredicted turbulences, like stochastic arrival or uncertainty delivery date, machine failure, and shortage of raw material, etc., which may trigger a variety of scheduling problems.
International Journal of Advanced Manufacturing Technology, 42(3–4):312–320. (2009) [3] M.
Journal of Computing and Information Science in Engineering, 7(3):259–268. (2009) [4] P.
Proceedings of the Institution of Engineers Part B-Journal of Engineering Manufacture, 223(11):1367–1387. (2009) [5] K.
International Journal of Computer Integrated Manufacturing, 19(4):383–392. (2006) [7] R.

Acknowledgments The work is supported by National Science and Technology Major Project (2009ZX04014-066-03) and National High Technology R&D Program of China (2009AA044302) References [1] Z.Y.
Liu: Journal Harbin UNIV.SCI.
Liu, and L.XIAO: Journal Harbin UNIV.SCI.
[4] W.S.QIN and G.R.WENG: Journal of Soochow University (Engineering Science Edition), Vol. 26 (2006) No.4, pp.7-10
LIU: Journal of Tool Technology, Vol. 40 (2006) No.8 pp.3-5.