Search results

According to literatures[3,4], with amine monomers of different structures and phenolic compound of different structures, it can synthesize benzoxazine monomers that can meet different demands.
Result and Discussion Structural analysis At B3LYP/6-311+G (d, p) level, geometry optimization and frequency calculation were conducted for the possible conformation of ketonic structure and alcohol structure of TMIPT molecule (gaseous phase).
Thus, it revealed that kentoic structure was far more stable than alcohol structure.
Organic Chemistry, High Education Press, Beijing2001, 8
Physic Chemistry, Science Press, Beijing2008, 556~557

The results show that the emulsion particles possess a clear core-shell structure.
Then the core-shell structure P(VAc-BA) emulsion is obtained.
As shown in Figure 2, the P(VAc-BA) emulsion particles present core-shell structure clearly.
Chemistry and adhesion, 2010, 32(1) : 54-56
Journal of Polymer Science: Polymer Chemistry Edition, 1980, 18(11): 3219-3228

Single Crystal Growth and Structure Analysis of AB-type Carbonate Apatite Y.
Introduction Carbonate ions included in the crystal structure of biological apatites are significantly related with the chemical properties of bone and teeth.
Therefore, to understand the configuration of carbonate ions in the apatite structure is important for the development of apatitic biomaterials.
Refinement of the structure was undertaken using a program of Xtal 3.4 [3].
[4] J.C.Elliott: Studies in Inorganic Chemistry 18, Structure and Chemistry of the Apatites and Other Calcium Orthophosphates, (Elsevier Science B.V., the Netherlands 1994).

Influence of Polyelectrolytes on the Processes of Structure Formation of Copper Powders Yu.M.
The processes occurring in the presence of water-soluble polymers and their influence on the structure of the obtained ultrafine copper powders are described.
Because of their small size, such structures have special physical and chemical properties, and opened a new large area fundamental research, and such are of interest for many applications.
Switzer, Electrochemical Deposition of Copper(I) Oxide Films, Chemistry of Materials 8 (1996) 2499-2504
Mendeleeva, Russian journal of organic chemistry journal of the Russian chemical society.

Introduction Chiral is the one of the key words in our recent chemistry world.
Chiraty materials have different chemistry effects respectively, for instance, Cisplatin is effective to defeat cancer, but Transplatin did not have this effect, even they have the same chemistry content, and some enzymes express the same phenomena.
After the chiral phenomenon had been discovered by distinguish chemistry scientist, they have been increasingly researched, especially in organic chemistry, pharmaceutical chemistry, and some scientists have been honored Nobel price for their work about the chiral chemistry, however, chiral work have some flaws, take the organic synthesis as example, several chiral organic had been synthesized using the homogeneous chiral catalyst, and it is difficult to separate them, but inorganic catalyst can solve this problem to some extent, so chiral inorganic material can also be employed in chromatography and other fields, therefore, it is necessary to generalized chiral inorganic material works of the past, and make a development .
The alignment and self-assembly of nanotubes into more complicated structures are growing challenges [13].
Many organisms also have helical structures, such as Spirulina and Helicobacter pylori.

Holler 5 1 Centrohem, Karadjordjeva 129, 22300 Stara Pazova, Serbia 2 Faculty of Physical Chemistry, University of Belgrade, Studentski trg 12-16, 11001 Belgrade, Serbia 3 Institute of General and Physical Chemistry, Studentski Trg 12-16, 11001 Belgrade, Serbia 4Faculty of Chemistry, University of Belgrade, Studentski trg 12-16, 11001 Belgrade, Serbia 5 Institute of Macromolecular Chemistry, Academy of Sciences of the Czech Republic, Heyrovský Sq. 2, 162 06 Prague 6, Czech Republic a cenhem@verat.net Keywords: Chemical oxidative polymerization, Coupling reactions, MNDO-PM3, Molecular structure, Morphology, Polyacriflavine, Semiconducting polymer.
The formation of phenazine rings in ladder structured polymerization products was observed by FTIR spectroscopy.
The existence of a certain polyacriflavine crystalline structure was suggested from the SEM micrographs.
The restricted Hartree-Fock method (RHF) was used for the molecular structures and the unrestricted Hartree-Fock (UHF) method for radical species.
[17] CRC Handbook of Chemistry and Physics, Ed.

Apparently, a single phase of sillenite structured bismuth titanate was obtained at 600˚C.
A sillenite structured bismuth titanate was formed at 600oC.
Chemistry of Materials, Vol. 20 (2008), p.2621 [9] Murray, C., Norris, D., & Bawendi, M.
Chemistry Society, Vol 115 (1993), p.8706 [10] Williams, J.
Chemistry of Material, Vol. 7 (1998), p.1764 [13] Lee, S.

The interfacial structures of a metal alloy film on SiC are very complicated after annealing.
Ti3SiC2 is responsible for ohmic contact formation on Ti/Al/p-SiC structures.
Our previous results [5] found that an additional carbon film, i.e., Ti/Al/C/SiC structure, exhibits some improvement of ohmic contacts on p-type SiC, compared to the Ti/Al/p-SiC structure.
As shown in Figure 2, only the C/Al/SiC structure shows ohmic behavior.
Lukehart at the Department of Chemistry of Vanderbilt University for the XRD measurements.

This work is based on CMOS transistor test structures with a nominal 28nm gate length.
The test structures stack consisted of doped polysilicon/Titanium Nitride (TiN) gates/ High K.
For the wet process, we selected various alkaline chemistries in the test.
U-5 shows better nitride and oxide loss among all chemistries, as shown in Figure 1.
(a) (b) Figure 4: No impact to TiN layer from over processing with wet chemistry.

Due to its inertness, SiC cannot be easily structured by wet chemical processes at room temperature.
The porous SiC layer can be used e.g. for structuring purposes [2] or e.g. as seed layer for the growth of a SiC epitaxial layer with improved properties [3,4].
One main advantage of the novel tool concept is that only one side of the wafer is contacted with chemistry which ensures single side processing.
The pore structure is homogenous over the complete porous layer thickness.
A scanning electron microscope picture of the obtained pore structure can be seen in figure 3a and b.