Search results

El-Bahar, S.
Olikh et al.: J.
Baba et al.: J.
Gudkov et al.: J.
Vlasiuk et al.: J.

In order to test the suitability of developed materials for application in the construction of photovoltaic cells, a series of dye-sensitized solar cells ITO/TiO2/dye/active layer/Al were prepared.
Dobrzański, et.al., Graphene-based layers deposited on to flexible substrates: Used in dye-sensitized solar cells as counter electrodes, Appl Surf Sci. 424 (2017) 157-163
Al-Kahlout, ZnO nanoparticles and porous coatings for dye-sensitized solar cell application: Photoelectrochemical characterization, Thin Solid Films 520 (2012) 1814-1820
Al-Ghamdi, Zarah H.
Gafer, Farid El-Tantawy, F.

Lange et al. [10] proposes, based on the TEM analysis, that water reacts with Y2O3 to form crystallites of Y(OH)3.
A similar mechanism was proposed by Hernandez et al [30].
Similar tendency was reported by Guicciardi et al. [35], Paul et al. [36], Wu [37], Eichler [38], and Suresh [39].
Li et al. [41] investigated the aging sensibility of Al2O3-doped 3Y-TZP by aging at 370 K in hot under 100 MPa stress.
El-Hout: J.

At the duct inlet, a prescribed velocity condition was also imposed, set at 3.3 m/s, as defined by Vaz et al. [4].
The numerical model employed here has been verified and validated in previous studies, and further details on these procedures can be found in Vaz et al. [4] and Rodrigues et al. [7]; as well as the mesh and geometries used here, which were verified in Vaz et al. [25].
This simplification was justified in Vaz et al. [4].
El Mankibi, L.
[23] A.L.

[61] A.L.
[62] A.L.
El- Bially, R.
Abd El-Hamid, R.A.
Burt, A.L.

These results are also in line with the research conducted by Tracey, et al. (2020).
These results are similar to the research conducted by Ni, et al. (2021).
And corroborated by the results of research conducted by Dacrory, et al. (2020).
El Ashry, H.
Al-Wafi, M.

Nevertheless, according to Trent et al. [3] and Gekonde et al. [4] abrasion wear is the dominant wear mode when the contact at the tool-chip interface is of a sliding contact nature.
Jiang et al. [8] conducted sliding wear tests on nickel alloys performed on a pin-on-disk facility.
Muller et al. [35] have done a work on the same material and under the same cutting conditions.
El Mansori, A.
El Mansori, A.

In this context, for the membrane system maintaining unchanged total pressure in both feed side and permeate side, Wijmann et al. [13], Yeom et al. [14], and Zhao et al. [15] defined CPC in a collateral manner, using a coefficient for individual membrane side to consider the polarization effect even on the downstream side.
For example, Caravella et al. [20] determine the CPC for permeation of hydrogen across Palladium based membranes applying the Sieverts characteristic driving force.
Davis, A.L.
El-Din, A.
El-Gendi, N.

Biciu et al. [16] have proposed a different approach.
Recently, Mabrouk et al. [13] used the concept of automatic ANN.
[16] 2011 Gabor+PCA SVM and BPNN NA AUC=0.95 Beura et al
[8][5] 2015 GLCM+DWT BPNN 332 AUC=0.97 Ergin et al
The resultant AUC presented by this paper is comparable to other AUC values of recent publications illustrated in table 2.Fig. 11: Obtained AUC while varying the value of the parameter h Fig. 12: ROC curve corresponding to a subset of 1000 ROIs images from the DDSM databaseTable 2: Az values for different methods in the state of the based abnormalities detection and the proposed one Author Feature Classifier Results Biciu et al. [16] Gabor and PCA SVM and BPNN AUC=0.95 Beura et al. [8][5] GLCM and DWT BPNN AUC=0.97 Bajaj et al. [10] BEMD LS-SVM Acc=95% Singh et al. [14] WCS-LBP SVM-REF anf RF Acc=95% Wang et al. [11] WFRFT and PCA Jaya-FNN Acc=92.27% Rampun et al. [12] LPQ SVM Acc=86.13% Rampun et al. [12] LPQ SVM Acc=86.13% MAbrouk et al. [13] shape, texture, and moment invariant features automatic ANN Acc=97% Gargouri et al.

Gantzer, A.L.
Al-Abed, J.
El-Mehaisin: Arch.
Murphy, A.L.
Gantzer, A.L.