Search results

Song et al. [18] that an addition of concentrated HCl in the reaction was crucial for forming h–MoO3 structure.
Irmawarti et al. [20] concluded that h–MoO3 structure was generated from high H+ concentration of the HNO3 and HCl.
Jitti-a-porn et al. [23] and demonstrated in Fig. 4 (b, c) and Table 1.
El-Shall, Synthesis and characterization of photochromic molybdenum and tungsten oxide nanoparticles, Nanostruct.

Yan et al [12] successfully obtained three kinds of In2O3 structures, nanowires, novel nanoarrows and nanorods, by introducing the catalyst and by changing source materials.
Andreas Menzel et al. found that with the assistance of COMSOL Multiphysics software [17], modelling the gas flow during the growth is useful in evaluation of the general behavior of the process under specific conditions.
Hao et al [33] reported that the growth rate perpendicular to three different low-indexed crystallographic planes was proportional to the surface energies, γ{111}<γ{100}<γ{110}, so the growth rates along three growth directions had such relationships: r<111>.
El-Maghraby, T.

The material behavior is considered linear elastic, but geometric nonlinearity is introduced in the analysis as has already been addressed by Han et al. [23].
For that purpose, the Green-Lagrange strain tensor is used and can be written as linear and nonlinear parts as follows: E = EL + EN = BLU + BNU, (2) where BL and BN correspond to the linear and nonlinear transformation matrices between nodal displacements, U, and element strains, E, respectively.
According to Buhl et al. [24], this is an artificial problem since these elements should be void and their behavior should not influence the structural response.
However, it was also mentioned by Buhl et al. [24] the noneffectiveness ofthese approaches, being suggested the relaxation of the convergence criterion for the equilibrium iterations.

Fits by Gans theory Renteria et al. [30] have demonstrated that the Gans theory is adequate for sol-gel systems.
Marzán et al. [28] have reported the reduction of silver ions with several surfactants dissolved in different solvents.
El-Sayed, J.
[17] A.L.

.% Al, 5.57 wt.% Mo, 5.04 wt.% V, -0.81 wt.% Cr, 0.98 wt.% Fe, Ti base (Russian alloy VT22) was selected as the initial material.
Treatment UTS ± 20, MPa YS ± 20, MPa El ± 0.5, % All-round pressing (ARP) 1630 1530 9.5 ARP + SP tension at 823 К [22] 1600 1560 4 ARP + SP compression at 823 К 1560 1520 8 ARP + SP compression at 823 К + annealing 723 K 5 hours 1630 1590 7 ARP + SP compression at 803 К 1610 1530 8.5 This results in an extended duration during which the workpiece is exposed to elevated temperatures.
Velay, Initial microstructure influence on Ti–Al–Mo–V alloy's superplastic deformation behavior and deformation mechanisms, Mat.
Naidenkin, Influence of low-temperature annealing time on the evolution of the structure and mechanical properties of a titanium Ti-Al-V, Physics of Metals and Metallography. 116(3) (2015) 302-308. doi: 10.1134/S0031918X15030114

Beck), el.singheiser@fz-juelich.de (L.
Drag reduction between 5 and 6% was confirmed through numerical computations by Choi et al. [4].
The riblets investigated by Bechert et al. [1] were made in plastic materials.
Fig. 1: Efficiency vs. producibility of different riblet geometries In Romans et al. [11] finite element simulations were performed with Abaqus/Standard.

Zhang et al [5] mentioned that task allocations and work-cell layout design become the major issues from HMC while Pearce et al [19] mentioned considering the factor of ergonomics to reduce physical strain occurs by humans and increase safety for the operator.
El Maraghy, M.
Timo et al., “Agent-based communication to map and exchange shop floor data between MES and material flow simulation based on the open standard CMSD,” IFAC- PapersOnLine, vol. 49, no. 12, pp. 1526–1531, 2016, doi: 10.1016/j.ifacol.2016.07.796.

Design and Development of a Measurement System Dedicated to Estimate the Junction Temperature of Insulated Gate Bipolar Transistor Modules Badredine Lamuadni1,a*, Rachid El Bouayadi1,b, Aouatif Amine1,c, Driss Zejli1,d 1ASEL, Advanced Systems Engineering Laboratory, Ibn Tofail University, National School of Applied Sciences, BP 242, Av. de l'université, Kenitra, Morocco.
Dupont et al. [10] carried out a comparison of these different parameters in the case of IGBT devices.
Jakopovic et al. [11] demonstrated that the temperature measured by thermo-sensitive electrical parameters is dependent on the dissipation condition.

But Stucky et al. were focused on electrochromic properties and Yu et al. did not measure I-V curves.
Frank et al. [42].
[6] a) A.L.
[11] a) E.L.
[13] a) E.L.

The kinetic study was conducted as described by Nnaji et al. [2].
This conforms with the previous finding reported by Ugwu et al. [54].
This finding conforms with that of Salem et al. [57] for COD and BOD at the receiving drainage basin.
Separation Science and Technology, 52:8, 1341-1349/ [77] El Maguana, Y., Elhadiri, N., Bouchdoug, M., Benchanaa, M., & Boussetta, A. (2018).
Journal of Chemistry, 2018. https://doi.org/10.1155/2018/2093654 [78] Al-Othman, Z.