Pull-Out Resistance of 3D Woven Sandwich Composites

Abstract:

3D woven sandwich composites are being developed for transportation applications such as for light train flooring. For those applications, the joining process of these materials is needed. Mechanical joining is a common and preferable method for this purpose. In mechanical joints, it is critical to consider the pull-out resistance of the joint. This study investigated the pull-out resistance of a fiberglass-polyester 3D woven sandwich composite mechanical joint by adapting ASTM D7332 procedure B. The results indicate that increasing the hole depth and diameter enhances both the failure load and maximum load of the joints. Moreover, inserts significantly enhance failure load and maximum load (292% and 198% respectively) due to increased contact area, leading to improved mechanical joint performance. Specimens without inserts only showcased crack, crazing, and out-of-plane shear failure modes on composite while additional damage on insert and potting material was observed on with-insert specimens. The optimal mechanical joint configuration utilized an insert, featuring a hole depth matching the sandwich composite thickness (20 mm) and a hole diameter of 9 mm resulting in a failure load of 1690 N and a maximum load of 3042 N.

• Periodical: Key Engineering Materials (Volume 1020)
• Pages: 11-28
• DOI: https://doi.org/10.4028/p-prZ2e1
• Online since: August 2025
• Authors: Syahwira Taqwa Triadi, Larasati Irischa Ramadhani, Riza Wirawan, Hermawan Judawisastra*
• Keywords: 3D Sandwich, Composite, Failure Load, Maximum Load, Pull-Out

References

[1] W. D. Callister Jr and D. G. Rethwisch, Callister's materials science and engineering. John Wiley & Sons, 2020.

[2] Y. Zhang, "Development and application of lightweight high strength organic materials," in MATEC Web of Conferences, 2018, vol. 207, p.3009.

DOI: 10.1051/matecconf/201820703009

[3] P. K. Mallick, Processing of Polymer matrix composites: processing and applications. CRC Press, 2017.

[4] D. Zenkert, The handbook of sandwich construction. Engineering Materials Advisory Services, 1997.

[5] A. W. Van Vuure, J. A. Ivens, and I. Verpoest, "Mechanical properties of composite panels based on woven sandwich-fabric preforms," Compos. Part A Appl. Sci. Manuf., vol. 31, no. 7, p.671–680, 2000.

DOI: 10.1016/s1359-835x(00)00017-8

[6] R. W. Messler, Joining of materials and structures: from pragmatic process to enabling technology. Butterworth-Heinemann, 2004.

[7] H. Judawisastra, "Pengembangan Material Ringan Berbasis Komposit Sandwich sebagai Pelapis Lantai Kereta LRT PT.INKA," 2018.

[8] D. Daniel, S. T. Triadi, R. Wirawan, E. Prajetelistia, and H. Judawisastra, "Pull-out resistance study of mechanical joints on sandwich materials : a review," Plast. Rubber Compos., 2022.

DOI: 10.1080/14658011.2021.2020030

[9] T. Lapid, C. Bil, and G. Hanlon, "Honeycomb Panel Insert Bolt Pull-Out Testing of a New Fast Curing Adhesive," Trans. Japan Soc. Aeronaut. Sp. Sci. Aerosp. Technol. Japan, vol. 15, no. APISAT-2016, pp. a53–a60, 2017.

DOI: 10.2322/tastj.15.a53

[10] R. Seemann and D. Krause, "Numerical modelling of partially potted inserts in honeycomb sandwich panels under pull-out loading," Compos. Struct., vol. 203, p.101–109, 2018.

DOI: 10.1016/j.compstruct.2018.07.028

[11] P. Kumsantia, B. Castanié, and P. Bunyawanichakul, "An investigation of failure scenario of the metallic insert in sandwich structures," 2010.

[12] S. Heimbs and M. Pein, "Failure behaviour of honeycomb sandwich corner joints and inserts," Compos. Struct., vol. 89, no. 4, p.575–588, 2009.

DOI: 10.1016/j.compstruct.2008.11.013

[13] G. Bianchi, G. S. Aglietti, and G. Richardson, "Optimization of bolted joints connecting honeycomb panels," 2007.

[14] K.-I. Song, J.-Y. Choi, J.-H. Kweon, J.-H. Choi, and K.-S. Kim, "An experimental study of the insert joint strength of composite sandwich structures," Compos. Struct., vol. 86, no. 1–3, p.107–113, 2008.

DOI: 10.1016/j.compstruct.2008.03.027

[15] M.-Y. Yang, H.-C. Hung, and J.-C. Kuo, "Characteristic of the insert joint strength of composite sandwich panel of formosat-5 remote sensing instrument," in ECCM16-16TH European Conference on Composite Materials, 2014, vol. 1.

[16] R. Roy, K. H. Nguyen, Y. B. Park, J. H. Kweon, and J. H. Choi, "Testing and modeling of NomexTM honeycomb sandwich Panels with bolt insert," Compos. Part B Eng., vol. 56, p.762–769, 2014.

DOI: 10.1016/j.compositesb.2013.09.006

[17] N. Raghu, M. Battley, and T. Southward, "Strength variability of inserts in sandwich panels," J. Sandw. Struct. Mater., vol. 11, no. 6, p.501–517, 2009.

DOI: 10.1177/1099636209104524

[18] J. Wolff, M. Brysch, and C. Hühne, "Validity check of an analytical dimensioning approach for potted insert load introductions in honeycomb sandwich panels," Compos. Struct., vol. 202, p.1195–1215, 2018.

DOI: 10.1016/j.compstruct.2018.05.105

[19] T. Center, Insert Design Handbook. ESA Publication Division, 1987.

[20] ASTM, "ASTM 7332 - Standard Test Method for Measuring the Fastener Pull-Through Resistance of a Fiber-Reinforced Polymer Matrix Composite 1," Astm, vol. i, no. C, p.1–12, 2015.

DOI: 10.1520/d7332_d7332m-09

[21] J. W. Lim, "Development of the hybrid insert for composite sandwich satellite structures," Compos. Part A Appl. Sci. Manuf., vol. 42, no. 8, p.1040–1048, 2011.

[22] G. Bianchi, G. S. Aglietti, and G. Richardson, "Static performance of hot bonded and cold bonded inserts in honeycomb panels," J. Sandw. Struct. Mater., vol. 13, no. 1, p.59–82, 2011.

DOI: 10.1177/1099636209359840