Characterizing the Microstructure and Performance of Mechanical Properties in Polylactic Acid/Copper Metal Infill Polymer Composites Fabricated through Fused Deposition Modeling

Abstract:

This study investigates polymer component manufacturing using fused deposition modeling, specifically focusing on the thermoplastic PLA-Cu in open-source FDM machines. Mechanical characteristics are explored, emphasizing infill density, pattern, and nozzle temperature. FDM-produced PLA-Cu specimens, varying in infill (60%, 80%, 100%) and patterns (TRIANGLE, HEXAGON, LINE), reveal superior mechanical properties in those with 100% density, TRIANGLE pattern, and a 210° nozzle temperature. ASTM-standard tests measure tensile and flexural strength, and scanning electron microscopy examines micro-morphology. Results indicate a correlation between increased strain rate and higher yield stress and elastic modulus in PLA-Cu specimens, emphasizing its engineering potential.

• Periodical: Key Engineering Materials (Volume 1037)
• Pages: 163-171
• DOI: https://doi.org/10.4028/p-ZAh7YJ
• Online since: January 2026
• Authors: K. Kiran*, B.R. Kannan, R.R. Rinto, N. Suprateek
• Keywords: FDM, Mechanical Properties, Microstructure, PLA, Polymer Composites

References

[1] C. Hu and Q.H. Qin, "Advances in Fused Deposition Modeling of Discontinuous Fiber/Polymer Composites," Current Opinion in Solid State Materials Science, vol. 24, no. 5, p.100867, 2020.

DOI: 10.1016/j.cossms.2020.100867

[2] P.K. Penumakala, J. Santo, and A. Thomas, "A Critical Review on the Fused Deposition Modeling of Thermoplastic Polymer Composites," Composites Part B, vol. 201, p.108336, 2020.

DOI: 10.1016/j.compositesb.2020.108336

[3] Rajesh Narayana Perumal and Venkatraj Athikesavan, "Studies on 0.95 Bi0.5(Na0.40K0.10) TiO3-0.05(Ba0.7Sr0.3)TiO3 ceramics for piezoelectric applications under different sintering temperature," Ferroelectrics, vol. 540, no. 1, pp.65-71, 2019.

DOI: 10.1080/00150193.2019.1611107

[4] Krishnan Ravi Kumar, KothavadyMylsamyMohanasundaram, Ramanathan Subramanian, Balasubramaniam Anandavel, "Influence of fly ash particles on tensile and impact behaviour of aluminium (Al/3Cu/8.5Si) metal matrix composites," Science and Engineering of Composite Materials, vol. 21, no. 2, p.181–189, 2014.

DOI: 10.1515/secm-2013-0006

[5] K.B. Mustapha and K.M. Metwalli, "A Review of Fused Deposition Modelling for 3D Printing of Smart Polymeric Materials and Composites," European Polymer Journal, vol. 156, p.110591, 2021.

DOI: 10.1016/j.eurpolymj.2021.110591

[6] K. Ravikumar, K. Kiran, V.S. Sreebalaji, "Characterization of mechanical properties of aluminium/tungsten carbide composites," Measurement, vol. 102, p.142–149, 2017.

DOI: 10.1016/j.measurement.2017.01.045

[7] R.B. Kristiawan, F. Imaduddin, D. Ariawan, and Z. Arifin, "A Review on the Fused Deposition Modeling (FDM) 3D Printing: Filament Processing, Materials, and Printing Parameters," Open Engineering, vol. 11, no. 1, p.639–649, 2021.

DOI: 10.1515/eng-2021-0063

[8] K. Ravi Kumar, K. Kiran, V.S. Sreebalaji, "Microstructural characteristics and mechanical behaviour of aluminium matrix composites reinforced with titanium carbide," Journal of Alloys and Compounds, vol. 723, pp.795-801, 2017.

DOI: 10.1016/j.jallcom.2017.06.309

[9] Aravinth Karuppanan, Venkatraj Athikesavan, P. Balaji Bhargav, P. Ramasamy, "Synthesis and characterization of K0.5Bi0.5TiO3-BaTiO3 piezoelectric ceramics for energy storage applications," Journal of Materials Science: Materials in Electronics, vol. 32, pp.717-726, 2021.

DOI: 10.1007/s10854-020-04851-0

[10] A. Dey and N. Yodo, "A Systematic Survey of FDM Process Parameter Optimization and Their Influence on Part Characteristics," Journal of Manufacturing and Materials Processing, vol. 3, no. 3, p.64, 2019.

DOI: 10.3390/jmmp3030064

[11] M. Nallusamy, K. Kiran, M. Suriyaprakash, "Evaluation of metallurgical characterization and mechanical properties of AA7075/ZrB2 in situ AMCs after friction stir processing," Surface Review and Letters, vol. 29, no. 05, 2022, 2250064.

DOI: 10.1142/s0218625x22500640

[12] U. Cevik and M. Kam, "A Review Study on Mechanical Properties of Obtained Products by FDM Method and Metal/Polymer Composite Filament Production," Journal of Nanomaterials, vol. 21, 2020, 6187149.

DOI: 10.1155/2020/6187149

[13] K. Kiran, K. Ravikumar, VS Sree Balaji, "Effect of B4C and graphite particulates on the mechanical and microstructural characteristics of AA 5052 hybrid composites," Materials Today: Proceedings, vol. 27, pp.2935-2940, 2020.

DOI: 10.1016/j.matpr.2020.03.519

[14] Rajesh Narayana Perumal, Venkatraj Athikesavan, "Structural and electrical properties of lanthanide-doped Bi0.5(Na0.80K0.20)0.5TiO3-SrTiO3 piezoelectric ceramics for energy-storage applications," Journal of Materials Science: Materials in Electronics, vol. 31, pp.4092-4105, 2020.

DOI: 10.1007/s10854-020-02956-0

[15] M. Nallusamy, A. G. Karthikeyan, K. Kiran, "Experimental Research Of Parametric Optimization On Wire Electrical Discharge Machining Of AA7075/ZrB2 In Situ Composites," Surface Review and Letters, vol. 29, no. 09, 2022, 2250121.

DOI: 10.1142/s0218625x22501219

[16] M. Kamaal, M. Anas, H. Rastogi, N. Bhardwaj, and A. Rahaman, "Effect of FDM Process Parameters on Mechanical Properties of 3D Printed Carbon Fibre–PLA Composite," Progress in Additive Manufacturing, vol. 6, no. 1, p.63–69, 2021.

DOI: 10.1007/s40964-020-00145-3

[17] Rajesh Narayana Perumal, Venkatraj Athikesavan, Prita Nair, "Influence of lead titanate additive on the structural and electrical properties of Na0.5Bi0.5TiO3-SrTiO3 piezoelectric ceramics," Ceramics International, vol. 44, no. 11, pp.13259-13266, 2018.

DOI: 10.1016/j.ceramint.2018.04.155

[18] K. Kiran, K. Ravi Kumar, M. SuriyaPrakash, M. Vijay Kumar, "Experimental Investigation on Wear Behaviour of AA6082 Aluminium Alloy, Tungsten Carbide and Graphite Hybrid Composites."

DOI: 10.46532/978-81-950008-1-4_107

[19] M. Araya-Calvo, I. Lo´pez-Go´mez, N. Chamberlain-Simon, J.L. Leo´n-Salazar, T. Guille´n-Giro´n, J.S. Corrales-Cordero, and O. Sa´nchez-Brenes, "Evaluation of Compressive and Flexural Properties of Continuous Fiber Fabrication Additive Manufacturing Technology," Additive Manufacturing, vol. 1, no. 22, p.157–164, 2018.

DOI: 10.1016/j.addma.2018.05.007

[20] Rajesh Narayana Perumal and Venkatraj Athikesavan, "Investigations on electrical and energy storage behaviour of PZN-PT, PMN-PT, PZN–PMN-PT piezoelectric solid solutions," Journal of Materials Science: Materials in Electronics, vol. 30, pp.902-913, 2019.

DOI: 10.1007/s10854-018-0361-x

[21] X. Zhang and L. Chen, "Effects of Laser Scanning Speed on Surface Roughness and Mechanical Properties of Aluminum/Polylactic Acid (Al/PLA) Composites Parts Fabricated by Fused Deposition Modeling," Polymer Testing, vol. 91, p.106785, 2020, DOI:b.

DOI: 10.1016/j.polymertesting.2020.106785

[22] M.A. Ryder, D.A. Lados, G.S. Iannacchione, and A.M. Peterson, "Fabrication and Properties of Novel Polymer-Metal Composites using Fused Deposition Modeling," Composites Science and Technology, vol. 12, no. 158, p.43–50, 2018.

DOI: 10.1016/j.compscitech.2018.01.049

[23] Rajesh Narayana Perumal, S. Sadhasivam, and Venkatraj Athikesavan, "Structural, dielectric, AC conductivity, piezoelectric and impedance spectroscopy studies on PbZr0.52Ti¬O3: RE3+ (RE3+: La3+, Nd3+ and Dy3+) ceramics," Results in Physics, vol. 15, p.102729, 2019.

DOI: 10.1016/j.rinp.2019.102729

[24] M. Azadi, A. Dadashi, S. Dezianian, M. Kianifar, S. Torkaman, and M. Chiyani, "High-Cycle Bending Fatigue Properties of Additive-Manufactured ABS and PLA Polymers Fabricated by Fused Deposition Modeling 3D-Printing," Forces Mech., vol. 3, 2021.

DOI: 10.1016/j.finmec.2021.100016

[25] F. Lupone, E. Padovano, A. Veca, L. Franceschetti, and C. Badini, "Innovative Processing Route Combining Fused Deposition Modelling and Laser Writing for the Manufacturing of Multifunctional Polyamide/Carbon Fiber Composites," Materials Design, vol. 193, p.108869, 2020.

DOI: 10.1016/j.matdes.2020.108869

[26] Venkatraj Athikesavan, S. Bhuvana, and G. Thilakavathi, "Structural and Electrical Properties of Pb(Mg1/3Nb2/3)O3-Pb(Yb1/2Nb1/2)O3-PbTiO3 Ternary Ceramic for Energy Storage Application," Ferroelectrics Letters Section, vol. 49, no. 4-6, pp.104-110, 2022.

DOI: 10.1016/j.ceramint.2011.03.059

[27] A.R. Zekavat, A. Jansson, J. Larsson, and L. Pejryd, "Investigating the Effect of Fabrication Temperature on Mechanical Properties of Fused Deposition Modeling Parts using X-ray Computed Tomography," International Journal of Advanced Manufacturing Technology, vol. 100, no. 1, p.287–296, 2019.

DOI: 10.1007/s00170-018-2664-8

[28] Venkatraj Athikesavan, E. Ranjith Kumar, and J. Suryakanth, "Evaluation of the structural and electrical properties of perovskite NKN-LN ceramics for energy storage applications," New Journal of Chemistry, vol. 46, no. 42, pp.20433-20444, 2022.

DOI: 10.1039/d2nj04420j

[29] A.L. Woern, D.J. Byard, R.B. Oakley, M.J. Fiedler, S.L. Snabes, and J.M. Pearce, "Fused Particle Fabrication 3-D Printing: Recycled Materials Optimization and Mechanical Properties," Materials, vol. 11, no. 8, p.1413, 2018.

DOI: 10.3390/ma11081413

[30] Venkatraj Athikesavan, M. Arulmani, and S. Bhuvana, "Evaluation of the structure and electrical properties of (1-x)Bi0.5(Na0.80K0.20)0.5TiO3-xLiNbO3 ceramic composite for piezoelectric sensor applications," International Journal of Modern Physics B, 2023, 2350280.

DOI: 10.1142/s0217979223502806