Axial Fatigue of PBF-LB Ti6Al4V: Process and Surface Effects

Abstract:

This study investigates the influence of layer thickness and surface condition on the microstructure and mechanical performance of Laser Powder Bed Fusion (PBF-LB) manufactured Ti6Al4V. Specimens were produced using two layer thicknesses, 40~µm and 80~µm, under identical process parameters. Characterization included tensile and axial fatigue testing, supported by microstructural analysis using field-emission scanning electron microscopy (FE-SEM) and electron backscatter diffraction (EBSD). Both processing conditions produced fully martensitic α′ microstructures, with the 40~µm builds showing finer lamellae and smaller prior-β grains due to higher cooling rates. Tensile tests revealed higher ductility for the 40~µm specimens while maintaining similar strength levels. Axial fatigue tests revealed better performance for lower layer thickness, electropolished surface and diagonal orientation. The results confirm that fatigue performance in PBF-LB Ti6Al4V is primarily governed by surface integrity and defect population rather than changes in microstructural morphology. Overall, finer layers and surface finishing enhance endurance strength, though at the cost of reduced build productivity.

• Periodical: Key Engineering Materials (Volume 1043)
• Pages: 43-49
• DOI: https://doi.org/10.4028/p-5lJm6K
• Online since: February 2026
• Authors: Timo Rautio*, Mikko Hietala, Matias Jaskari, Aappo Mustakangas, Antti Järvenpää
• Keywords: Fatigue Strength, PBF-LB, TiAl6V4

References

[1] F. Bartolomeu, M. Gasik, F.S. Silva, G. Miranda, Mechanical Properties of Ti6Al4V Fabricated by Laser Powder Bed Fusion: A Review Focused on the Processing and Microstructural Parameters Influence on the Final Properties, Metals 12 (2022) 986.

DOI: 10.3390/met12060986

[2] A. Dareh Baghi, S. Nafisi, H. Ebendorff-Heidepriem, R. Ghomashchi, Microstructural Development of Ti-6Al-4V Alloy via Powder Metallurgy and Laser Powder Bed Fusion, Metals 12 (2022) 1462.

DOI: 10.3390/met12091462

[3] S. Leuders, M. Thöne, A. Riemer, T. Niendorf, T. Tröster, H.A. Richard, H.J. Maier, On the mechanical behaviour of titanium alloy TiAl6V4 manufactured by selective laser melting: Fatigue resistance and crack growth performance, International Journal of Fatigue 48 (2013) 300-307.

DOI: 10.1016/j.ijfatigue.2012.11.011

[4] M.V. Gerov, E.Y. Vladislavskaya, V.F. Terent'ev, D.V. Prosvirnin, A.G. Kolmakov, O.S. Antonova, Fatigue strength of a Ti-6Al-4V alloy produced by selective laser melting, Russian Metallurgy (Metally) (2016) 935-941.

DOI: 10.1134/s0036029516100049

[5] F. Cao, T. Zhang, M.A. Ryder, D.A. Lados, A Review of the Fatigue Properties of Additively Manufactured Ti-6Al-4V, JOM 70 (2018) 349-357.

DOI: 10.1007/s11837-017-2728-5

[6] Z. Li, C. Affolter, High-Cycle Fatigue Performance of Laser Powder Bed Fusion Ti-6Al-4V Alloy with Inherent Internal Defects: A Critical Literature Review, Metals 14 (2024) 972.[7] N. Belsure, R. Sandberg, E. Hryha, G. Soundarapandiyan, F. Deirmina, Effect of Layer Thickness and Particle Size Distribution on the Microstructure and Properties of Ti6Al4V Processed by Laser Powder Bed Fusion, Key Engineering Materials 1009 (2025) 29-38.

DOI: 10.4028/p-atfb6c

[8] S. McConnell, Y. Beshay, K. Kourousis, D. Tanner, Increasing productivity for laser powder bed fusion of Ti-6Al-4V parts through increased layer thickness, Progress in Additive Manufacturing (2025).

DOI: 10.1007/s40964-025-01079-4