Analysis of Surface Reaction Mechanisms on Electrically Non-Conductive Zirconia, Occurring within the Spark Erosion Process Chain

Abstract:

Electrically insulating high performance ceramics like zirconia are increasingly used for high technological applications due to their extraordinary properties. Meanwhile even the spark erosion process can be used to structure non-conductive ceramics by using an assisting electrode (AE). This conductive AE is placed on top of the work piece to enable the process. The electrical contact is sustained during the process by carbonic residua of cracked oil used as a dielectric. For an enhanced understanding of the removal mechanisms during the spark erosion process of such non-conductive ceramics, we analysed the surface of ceramic samples during the entire spark erosion process chain. In our investigation a zirconium oxide with yttrium oxide stabilisation was chosen. For this purpose X-ray diffraction (XRD) and scanning electron microscopy (SEM) analysis was performed. The XRD results showed that the zirconium oxide reacts under the presence of carbonic residua during processing into zirconium carbide. This material supports sustaining the conductivity additionally, as it is conductive itself. In a subsequent thermal cleaning step with oxide atmosphere (T = 750°C), remaining carbonic residua are oxidised and thus removed. The XRD measurements after cleaning showed that the zirconium carbide was no longer detectable. Instead a monoclinic zirconium phase was found. This shows that a reverse reaction of zirconium carbide into zirconium oxide took place. To prevent the formation of a non-stabilised monoclinic phase, the oven process was adapted to higher temperatures of 900°C with higher heating and active cooling rates of up to 10 K/s. This adjustment shows that the monoclinic phase can be supressed and the reverse reaction leads to a tetragonal zirconium oxide like the bulk material.

• Periodical: Key Engineering Materials (Volumes 504-506)
• Pages: 1171-1176
• DOI: https://doi.org/10.4028/www.scientific.net/KEM.504-506.1171
• Online since: February 2012
• Authors: T. Hösel, Claas Müller, Holger Reinecke
• Keywords: EDM, Non-Conductive Ceramics, Surface Reactions, X-Ray Diffraction (XRD), Zirconia

References

[1] F. Klocke, W. König, Fertigungsverfahren 3: Abtragen, Generieren und Lasermaterialbearbeitung. Springer Verlag, 2007 ISBN: 978-3-540-23492-0

[2] G. Spur, Keramikbearbeitung. Schleifen, Honen, Läppen, Abtragen. Hanser Verlag, München - Wien, 1998 ISBN 3446156208

[3] B. Lauwers, J.P. Kruth, K. Brans, Development of Technology and Strategies for the Machining of Ceramic Components by Sinking and Milling EDM. Annals of the CIRP 2007 56/1

DOI: 10.1016/j.cirp.2007.05.053

[4] B. Lauwers, W. Liu, J.P. Kruth, J. Vleugels, D. Jiang, O. Van der Biest, Wire EDM machining of Si3N4, ZrO2 and Al2O3-based ceramics. International Journal of Electro Machining, 10 2005 33-37

DOI: 10.2526/ijem.10.33

[5] C. Morgan, R.R. Vallance, E.R. Marsh, Micro machining glass with polycrystalline diamond tools shaped by micro electro discharge machining. Journal of Micromechanics and Microengineering, 14 2004 1687–1692

DOI: 10.1088/0960-1317/14/12/013

[6] Y. Fukuzawa, T. Tani, E. Iwane, N. Mohri, New machining method for insulating ceramics with an electrical discharge phenomenon. J Ceram Soc Jpn, 103 (1995) 1000-1005

DOI: 10.2109/jcersj.103.1000

[7] Y. Fukuzawa, T. Tani, Y. Ito, Y. Ichinose, N. Mohri, Electrical Discharge Machining (EDM) Of Insulator Ceramics With A Sheet Of Metal Mesh. Proceedings of the ISEM-II, (1995) 173-179

[8] Y.F. Chen, Y.J. Lin, Y.C. Lin, S.L. Chen, L.R. Hsu, Optimization of electrodischarge machining parameters on ZrO2 ceramic using Taguchi method. Journal of Engineering Manufacture, 224 (2009) 195-205

DOI: 10.1243/09544054jem1437

[9] Y. Fukuzawa, N. Mohri, T. Tani, Electrical discharge machining phenomena of insulating sialon ceramics with an assisting electrode. International Journal of Electrical Machining. (1997)

DOI: 10.2526/ijem.2.25

[10] N. Mohri, Y. Fukusima, Y. Fukuzawa, T. Tani, N. Saito, Layer generation process on work-piece in electrical discharge machining. CIRP Annals - Manufacturing Technology, 52/1 2003 157-160

DOI: 10.1016/s0007-8506(07)60554-x

[11] Y.H. Liu, R.J. Ji, X.P. Li, L.L. Yu, H.F. Zhang, Q.Y. Li, Effect of machining fluid on the process performance of electric discharge milling of insulating Al2O3 ceramic. International journal of machine tools and manufacture, 48 2008 1030-1035

DOI: 10.1016/j.ijmachtools.2007.12.011

[12] U. Panten, Funkenerosive Bearbeitung von elektrisch leitfähigen Keramiken. PhD thesis, RWTH Aachen, (1991)

[13] T. Hösel, C. Müller, H. Reinecke, Simple techniques of applying lacquer based assisting electrodes for spark erosive structuring of electrically nonconductive zirconia (ZrO2). 4M/ICOMM 2009, The Global Conference on Micro Manufacture

DOI: 10.1016/j.cirpj.2011.05.005

[14] T. Hösel, C. Müller, H. Reinecke, Senkerosion von Mikrostrukturen in gesintertem, elektrisch isolierendem ZrO2. Proceedings Mikrosystemtechnik Kongress Berlin/Germany, (2009) 789-791

[15] F. A Modine, T. W. Haywood, C. Y. Allison, Optical and electrical properties of single-crystalline zirconium carbide. Physical Review, 32(12) 1985 7743-7747

DOI: 10.1103/physrevb.32.7743