Experimental Study on WEDM Machining of PCD and PCBN Compacts

Man Cang Song; Jian Lei Zhang; Chao Yu; Min Jie Wang; Chong Liu; Ying Liu

doi:10.4028/www.scientific.net/KEM.645-646.52

Paper Titles

Effect of Hydrophilic and Hydrophobic SiO₂ Particles on Performances of PI/Al₂O₃ Composite Films
p.26

Synthesis and Characterization of Topological Insulator Bi₂Te₃ Nanowires
p.32

Electronic and Magnetic Properties of Rare-Earth Atoms Absorbed on Graphene Sheet: A Theoretical Study
p.40

Melt Electrohydrodynamic Direct-Writing Micro/Nano Fiber with Restriction of Heated Sheath Gas
p.45

Experimental Study on WEDM Machining of PCD and PCBN Compacts
p.52

Wet Anisotropic Etching Characteristics of Si{100} in TMAH+Triton at near the Boiling Point
p.58

Hierarchically Ordered Porous Carbon as a Host Material for Energetic Composites
p.64

TCAD Study of the Raised SiGe Source/Drain in 40nm PMOS
p.70

Adsorption of Silver Nanoparticles on Modified Surfaces
p.75

HomeKey Engineering MaterialsKey Engineering Materials Vols. 645-646Experimental Study on WEDM Machining of PCD and...

Experimental Study on WEDM Machining of PCD and PCBN Compacts

Abstract:

Some typical kinds of PCD and PCBN compacts are selected to be machined by WEDM, and a series of processing tests are taken. After machining, the surface roughness of cutting section, the processing quality of cobalt-rich interface layer and the edge of superhard material layer are measured by surface profiler and 3D microscope. The results show that processing quality is affected by superhard particle size and concentration greatly, and better processing quality can be obtained after several cutting of WEDM. The minimum sharpening allowance of PCD cutting tools can be controlled within 4~15μm after WEDM, and within 10μm for PCBN BNX20, while BZN6000 needs larger follow-up workload of sharpening.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Key Engineering Materials (Volumes 645-646)

Pages:

52-57

DOI:

https://doi.org/10.4028/www.scientific.net/KEM.645-646.52

Citation:

Cite this paper

Online since:

May 2015

Authors:

Man Cang Song*, Jian Lei Zhang, Chao Yu, Min Jie Wang, Chong Liu, Ying Liu

Keywords:

Polycrystalline Cubic Boron Nitride (PCBN), Polycrystalline Diamond (PCD), Processing Quality, Wire Electric Discharge Machining (WEDM)

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] G. F. Zhang, Z. H. Deng. Cutting mechanism and surface appearance of PDC with WEDM. China Mech. Eng. ，18(6)(2007) 671-675(in Chinese).

Google Scholar

[2] J. Wang. The way to improve super-hard cutting tool material wire-cutting processing efficiency. Electromach. Mould，(4)(2004) 59-60(in Chinese).

Google Scholar

[3] K. Suzuki, Y. Shiraishi, N. Nakajima, et al. Development of new PCD made up of boron doped diamond particles and its machinability by EDM. Adv. Mater. Res. ， (76-78) (2009) 684-689.

DOI: 10.4028/www.scientific.net/amr.76-78.684

Google Scholar

[4] R. H. Olsen, R. C. Dewes, D. K. Aspinwall. Machining of electrically conductive CVD diamond tool blanks using EDM. J. Mater. Process. Technol. ， (149)(2004) 627-632.

DOI: 10.1016/j.jmatprotec.2003.11.052

Google Scholar

[5] P. Tso, Y. Liu. Study on PCD machining. Int. J. Mach. Tools Manuf., (42)(2002) 331-334.

Google Scholar

[6] Y. Jia, B. S. Kim, D. J. Hu, J. Ni. Parametric study on near-dry wire electrodischarge machining of polycrystalline diamond-coated tungsten carbide material. J. Eng. Manuf. ，224(2009) 185-194.

DOI: 10.1243/09544054jem1602

Google Scholar