Study on Microstructure Evolution and Wear Resistance Properties of Laser Cladding Applied on R900A Rail Steel

Abstract:

The current research aimed to study microstructure evolution and wear resistance properties of coating layers on R900A rail steel. Powdery type laser cladding was carried out employing a three-jet coaxial laser nozzle by using the 3650 (Chromium-Nickel steel) powder. The key laser cladding parameters included a laser power of 1 - 1.5 kW, a scanning speed of 5 - 15 mm/s, and a powder feed rate of 10 – 20 g/min. After laser cladding completion, the coated specimens were carried out into the pin-on-disc tribometer for abrasive wear resistance evaluation compared to the reference rail material. The specimens were weighed before and after the wear test by an electronic balance with 0.0001g resolution. The hardness test and microstructure evolution were performed on the cross-sectional area of the specimen. After the wear test, the worn surface profile and wear morphology of the tested specimen were evaluated to determine the wear mechanism and severity. The hardness test shows that the 3650 had a higher hardness than the conventional rail steel. The microstructure of coating surfaces was composed of various carbide compounds such as Cr₂₃C₆ and Cr₇C₃, which are distributed in the austenite matrix. Moreover, the 3650 cladding surface provided greater wear resistance than rail steel and not much difference in hardness, which is suitable for rail maintenance in a realistic situation.

• Periodical: Materials Science Forum (Volume 1173)
• Pages: 19-26
• DOI: https://doi.org/10.4028/p-FUfy1V
• Online since: December 2025
• Authors: Yuttanan Pukkate, Hathaipat Koiprasert, Panadda Sheppard, Ekkarut Viyanit, Pisak Lertvijitpun*
• Keywords: Laser Cladding, Rail Steel

References

[1] S. Kumar, u. Luleå tekniska universitet. Avdelningen för drift och, Study of Rail Breaks: Associated Risks and Maintenance Strategies : Technical Report, Division of Operation and Maintenance Engineering, Luleå University of Technology, 2006.

[2] L.P.F. de Almeida, L.E. Falqueto, H. Goldenstein, A C. Bozzi, C. Scandian, Study of sliding wear of the wheel flange - Rail gauge corner contact conditions: Comparative between cast and forged steel wheel materials, Wear. 432 (2019) 102894.

DOI: 10.1016/j.wear.2019.05.009

[3] H. Vasudev, Hardfaced layer on mild steel made by paste technique with SMAW electrode to improve surface properties, Indian Journal of Engineering and Materials Sciences. 1 (2014).

[4] J. Coronado, H. Caicedo, A. Gomez, The effects of welding processes on abrasive wear resistance for hardfacing deposits, Tribology International - TRIBOL INT. 42 (2009) 745-749.

DOI: 10.1016/j.triboint.2008.10.012

[5] C. He, G. Zou, X. Wang, H. Liu, P. Li, J. Liu, S. Lo, Effects of various laser cladding materials on the tribological properties of damaged wheel treads under various temperatures and humidities, Tribology International. 202 (2025).

DOI: 10.1016/j.triboint.2024.110374

[6] F. Franklin, G.J. Weeda, A. Kapoor, M. Hiensch, Rolling Contact fatigue and wear behavior of the infrastar two-material rail, Wear. 258 (2005) 1048-1054.

DOI: 10.1016/j.wear.2004.03.054

[7] A. Clare, O. Oyelola, J. Folkes, P. Farayibi, Laser cladding for railway repair and preventative maintenance, Journal of Laser Applications. 24 (2012) 032004.

DOI: 10.2351/1.4710578

[8] H. Ding, T. Yang, W. Wang, Y. Zhu, Q. Lin, J. Guo, Q. Xiao, L. Gan, Q. Liu, Optimization and wear behaviors of 316L stainless steel laser cladding on rail material, Wear. 523 (2023) 204830.

DOI: 10.1016/j.wear.2023.204830

[9] C. Chen, Q. Bai, Q. Li, C. Zhao, J. Zhang, S. Zhang, Study on the Performance of Fe-Based Alloy Coating on 40Cr Substrate Surface, Journal of Materials Engineering and Performance. 34 (2025) 1586-1595.

DOI: 10.1007/s11665-024-09157-4

[10] G. Li, Y. Gan, C. Liu, Y. Shi, Y. Zhao, S. Kou, Corrosion and Wear Resistance of Fe-Based Amorphous Coatings, Coatings. (2020).

DOI: 10.3390/coatings10010073

[11] J. Wahlström, A pin-on-disc tribometer study of friction at low contact pressures and sliding speeds for a disc brake material combination, Results in Engineering. 4 (2019) 100051.

DOI: 10.1016/j.rineng.2019.100051

[12] B. Ferdowsi, M. Griffa, R.A. Guyer, P.A. Johnson, J. Carmeliet, Effect of boundary vibration on the frictional behavior of a dense sheared granular layer, Acta Mechanica. 225 (2014) 2227-2237.

DOI: 10.1007/s00707-014-1136-y

[13] B. Singh and J. Grewal, Study of dry wear behavior of Novel ferrous samples prepared by powder metallurgy method, Surface Topography: Metrology and Properties. 10 (2022).

DOI: 10.1088/2051-672x/ac63d8

[14] Q. Luo, M. Kitchen, J. Li, W. Li, Y. Li, Experimental investigation on the spalling failure of a railway turnout made from Hadfield steel, Wear. 523 (2023) 204779.

DOI: 10.1016/j.wear.2023.204779