Dissimilar Friction Stir Welding of HSLA Steel to Austenitic High-Mn TRIP Steel

Ricardo Henrique Buzolin; Brianda Rangel Francisco; Erenilton Pereira da Silva; Victor Ferrinho Pereira; Antonio Jose Ramirez Londono; Omar Maluf; Haroldo Cavalcanti Pinto

doi:10.4028/www.scientific.net/MSF.879.2306

Paper Titles

Kinetics of Microstructure Refinement in Titanium Alloys during Deformation
p.2280

Needle Like Fe-Containing Intermetallic Compounds of High Silicon Aluminum Alloy with Fe Modified by Mn and Ultrasonic Vibration
p.2286

Microstructure and Mechanical Properties of Medium Manganese Steel Plate with High Strength and Toughness
p.2293

Effect of Mischmetal Additions and Solution Heat Treatments (T4) on the Microstructure and Mechanical Properties of Thixocast ZK60-RE Magnesium Alloys
p.2300

Effects of Warm Working on Microstructural and Shear Deformation Properties of TRIP-Aided Martenitic Steel
p.2312

Characterization of Phase Transitions Occurring in Solution Treated Ti-15Mo during Heating by Thermal Expansion and Electrical Resistance Measurements
p.2318

Microstructure and Creep Properties of Silicon- and/or Germanium-Bearing Near-α Titanium Alloys
p.2324

Formation and Dissolution of Hydride Precipitates in Zirconium Alloys: Crystallographic Orientation Relationships and Stability after Temperature Cycling
p.2330

HomeMaterials Science ForumMaterials Science Forum Vol. 879Dissimilar Friction Stir Welding of HSLA Steel to...

Dissimilar Friction Stir Welding of HSLA Steel to Austenitic High-Mn TRIP Steel

Abstract:

The microstructure and mechanical properties of dissimilar butt-joints between a high-strength low alloyed (HSLA) grade and an austenitic high Mn TRIP steel were investigated. The tool rotation and the tool offset toward the TRIP steel were varied between 300–500 rpm and 1–2 mm, respectively. Tool advancing speed amounted to 100 mm/min. Maximum tension stress was observed for the butt-joint welded with 300 rpm and 2 mm offset. The lowest increase in hardness within the stirred zone also occurred for this FSW condition, indicating that this tool rotation is more promising for welding dissimilar joints of commercial HSLA and high Mn TRIP steels. The weld microstructure consisted mainly of a stirred zone, and neither significant HAZ nor TMAZ are observed. However, two main lobular regions are observed, one at the bottom and another one at the top side of the welds. Besides, the HSLA develops a multiphase microstructure consisting of bainite, martensite and retained austenite phases, whereas no e/a martensite is found in the stirred zone of the austenitic high-Mn TRIP steel.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Materials Science Forum (Volume 879)

Pages:

2306-2311

DOI:

https://doi.org/10.4028/www.scientific.net/MSF.879.2306

Citation:

Cite this paper

Online since:

November 2016

Authors:

Ricardo Henrique Buzolin, Brianda Rangel Francisco, Erenilton Pereira da Silva, Victor Ferrinho Pereira, Antonio Jose Ramirez Londono, Omar Maluf, Haroldo Cavalcanti Pinto*

Keywords:

Dissimilar Welding, Friction Stir Welding, High Mn Steel, HSLA Steel, TRIP Steel

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] R.S. Mishra, and Z.Y. Ma, Friction stir welding and processing. Mat. Sci. Eng. R 50. 1 (2005) 1-78.

Google Scholar

[2] T. DebRoy, H.K.D.H. Bhadeshia, Friction stir welding of dissimilar alloys–a perspective. Sci. Technol. Weld. Joi. 15. 4 (2010) 266-270.

DOI: 10.1179/174329310x12726496072400

Google Scholar

[3] M. P Miles, et al., Effect of friction stir welding conditions on properties and microstructures of high strength automotive steel. Sci. Technol. Weld. Joi. 14. 3 (2009) 228-232.

DOI: 10.1179/136217108x388633

Google Scholar

[4] Y.S. Sato, et al., Evaluation of microstructure and properties in friction stir welded superaustenitic stainless steel. Sci. Technol. Weld. Joi. 14. 3 (2009) 202-209.

DOI: 10.1179/136217108x386518

Google Scholar

[5] Y.D. Chung, et al., Friction stir welding of hypereutectoid steel (SK5) below eutectoid temperature. Sci. Technol. Weld. Joi. 14. 3 (2009) 233-238.

DOI: 10.1179/136217109x415901

Google Scholar

[6] G. Frommeyer, U. Brux, P. Neumann, Supra-Ductile and High- Strength Manganese-TRIP/TWIP Steels for High Energy Ab- sorption Purposes. ISIJ Int. 43. 3 (2003) 438-446.

DOI: 10.2355/isijinternational.43.438

Google Scholar

[7] L. Mujica, S. Weber, H. Pinto, C. Thomy, F. Vollertsen, Microstructure and mechanical properties of laser-welded joints of TWIP and TRIP steels, Materials Science and Engineering A 527 (2010) 2071–(2078).

DOI: 10.1016/j.msea.2009.11.050

Google Scholar

[8] S. Allain, J. -P. Chateau, O. Bouaziz, S. Migot, N. Guelton, Correlations between the calculated stacking fault energy and the plasticity mechanisms in Fe–Mn–C alloys, Mat. Sci. Eng. A 387–389 (2004) 158–162.

DOI: 10.1016/j.msea.2004.01.059

Google Scholar

[9] R. Nandan, G. G Roy, T.J. Lienert, T. Debroy, Three-dimensional heat and material flow during friction stir welding of mild steel. Acta Mater. 55. 3 (2007) 883-895.

DOI: 10.1016/j.actamat.2006.09.009

Google Scholar

[10] L.Y. Wei, T.W. Nelson, Correlation of microstructures and process variables in FSW HSLA-65 steel. (2011) Weld. Journal, 90, 95-101.

Google Scholar

[11] S. Zaefferer, J. Ohlert, W. Bleck, A study of microstructure, transformation mechanisms and correlation between microstructure and mechanical properties of a low alloyed TRIP steel, Acta Mater. 52 (2004) 2765–2778.

DOI: 10.1016/j.actamat.2004.02.044

Google Scholar