Influence of Sintering Conditions on Microstructural and Mechanical Properties of an Yttria Partially Stabilized Zirconia

Fabiana Ribeiro da Silva Schanuel; Wilson Acchar

doi:10.4028/www.scientific.net/MSF.881.143

Paper Titles

Effect of CuO-TiO₂ Eutectic on Thermal and Electrical Conductivities of CaCu₃Ti₄O₁₂ Ceramics
p.117

Synthesis and Characterization of Nickel Manganite Ceramics by Polymeric Precursors Method
p.123

Estimate of the Anisotropy Field of Strontium Ferrite from Powders Using the Stoner-Wohlfarth Model
p.128

High Technology Applications of Barium and Strontium Ferrite Magnets
p.134

Influence of Sintering Conditions on Microstructural and Mechanical Properties of an Yttria Partially Stabilized Zirconia
p.143

Part II - Microstructural and Physical of Calcium Phosphate Biomaterials Obtained from Natural Raw Materials
p.147

Synthesis and Characterization of Nanostructured Calcium Phosphates: Colloidal Suspension Rheological Study
p.153

Synthesis and Characterization of a Nanostructured Matrix of Hydrated Calcium Phosphate
p.159

Synthesis and Characterization of a Hydrated Calcium Phosphate Matrix and Biphasic Compositions with MgO and α-Al₂O₃
p.165

HomeMaterials Science ForumMaterials Science Forum Vol. 881Influence of Sintering Conditions on...

Influence of Sintering Conditions on Microstructural and Mechanical Properties of an Yttria Partially Stabilized Zirconia

Abstract:

The aim of this study was to evaluate the dependence of sintering conditions on mechanical properties and microstructure of zirconia stabilized by yttria. Commercial blocks of pre-sintered of zirconia stabilized (DeguDent Dentsply, Germany-Cercon) were investigated in this study. The blocks belonging to group 1 were sintered under the recommended conditions by the manufacturer (1350°C for 6 hours). The blocks of group 2 were sintered under 1500°C for 6 hours. The blocks of group 3 were sintered under 1350 C for 14.5 hours. The results indicated that the sintering conditions influenced the mechanical properties and microstructure of zirconia. The three sintering conditions analyzed in this study produces zirconia bodies with properties adequate to be used in clinical function. However, the decisive factor for change in the sintering conditions should be the cost/benefit during the prosthetical process and longevity of clinical material to perform its function in the oral cavity.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Materials Science Forum (Volume 881)

Pages:

143-146

DOI:

https://doi.org/10.4028/www.scientific.net/MSF.881.143

Citation:

Cite this paper

Online since:

November 2016

Authors:

Fabiana Ribeiro da Silva Schanuel, Wilson Acchar

Keywords:

Dental Materials, Sintering Conditions, Zirconia

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

References

[1] T. Kosmac, C. Oblak and P. Jevnilar: Materials and Technology Vol. 5 (2007), p.237.

Google Scholar

[2] A.R. Curtis, A.J. Wright and G.J.P. Fleming: J. Dent. Vol. 34 (5) (2006), p.317.

Google Scholar

[3] S. Deville, J. Chevalier, C. Dauvergne and G. Fantozzi: J. Am. Ceram. Soc. Vol. 88 (2005), p.1273.

Google Scholar

[4] D.L. Porter and A.H. Heuer: J. Am. Ceram. Soc. Vol. 60 (1977), p.183.

Google Scholar

[5] A.F. Habibe, R.C. Souza, L.D. Maeda, L.A. Bicalho, M.J.R. Barboza and C. Santos: Tecnologia em Metalurgia e Materiais Vol. 4 (3) (2008), p.23.

DOI: 10.4322/tmm.00403005

Google Scholar

[6] J. Eichler, J. Rödel, U. Eisele and M. Hoffman: J. Am. Ceram. Soc. Vol. 90 (2007), p.2830.

Google Scholar

[7] J. Hjerppe, P.K. Vallittu, K. Fröberg and L.V. Lassila: Dent. Mater. Vol. 25 (2) (2009), p.166.

Google Scholar

[8] W. Acchar: Ceramic Materials: Science and Technology. (EDUFRN 1st. ed. Natal, 2000).

Google Scholar

[9] W.D. Kingery, H.K. Bowen and D.R. Uhlman: Introduction to Ceramics. (John Willey & Sons 1st ed. New York, 1976).

Google Scholar

[10] M. Guazzato, M. Albakry, S.P. Ringer and M.V. Swain: Dent. Mater. Vol. 20 (5) (2004), p.449.

Google Scholar