Microstructural Aspects of TBC`s Deposited on Internal Combustion Engine Valve Materials

Abstract:

The discs of the intake or exhaust valves are vital organs of internal combustion engines, being subjected to extreme operating conditions, thermal, mechanical and chemical types. One of the goals of researches in this area is related to thermal insulation of the combustion chamber of internal combustion engines, which could enhance their performance in operation. In this article we analysed the microstructural aspects of some coatings obtained from powders with thermal barrier role on specific materials for internal combustion engines valves. There were used as substrate samples of low alloy steels with Si and high alloyed steels with Cr, Ni and Mn. Using the facility SPRAYWIZARD 9MCE for atmospheric plasma spraying, two types of thermal barrier coatings were produced, from powders based on zirconia and alumina. The samples were analyzed in terms of microstructure using the QUANTA 200 3D scanning electron microscope and the X`PERT PROMD diffractometer. Observations were made both on the longitudinal surface of the coating in order to evaluate it and on the cross-section to evaluate the substrate-coating interface, the influence of deposition temperatures on the substrate and aspect/microstructure on its depth. XRD analysis revealed a cubic structure of aluminum oxide, respectively zirconium oxide. The identified morphology is a specific "splat" one for the ceramic coatings. Surface appearance shows tiny pores and cracks specific to the spraying method. The resulted coatings present a significant compactness and adherence to the substrate, which recommends them for further thermal behaviour testing.

• Periodical: Materials Science Forum (Volume 907)
• Pages: 151-156
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.907.151
• Online since: September 2017
• Authors: Marius Panțuru, Daniela Lucia Chicet*, Constantin Paulin, Ștefan Lupescu, Corneliu Munteanu
• Keywords: Atmospheric Plasma Spray, Internal Combustion Engines Valve, TBC

References

[1] Z.J. Sroka, Some aspects of thermal load and operating indexes after downsizing for internal combustion engine, J. Therm. Anal. Calorim. 110 (1) (2011) 51–58.

DOI: 10.1007/s10973-011-2064-x

[2] R. Lewis, R.S. Dwyer-Joyce, Automotive Engine Valve Recession, Engineering Research Series, London, (2002).

[3] P. Forsberg, P. Hollman, S. Jacobson, Wear mechanism study of exhaust valve system in modern heavy duty combustion engines, Wear. 271 (2011) 2477–2484.

DOI: 10.1016/j.wear.2010.11.039

[4] R. Elo, S. Jacobson, Formation and breakdown of oil residue tribofilms protecting the valves of diesel engines, Wear 330-331 (2015) 193–198.

DOI: 10.1016/j.wear.2015.01.066

[5] I. Taymaz, An experimental study of energy balance in low heat rejection diesel Engine, Energy. 31 (2006) 364-371.

DOI: 10.1016/j.energy.2005.02.004

[6] B. Iscan, Application of ceramic coating for improving the usage of cottonseed oil in a diesel engine, Journal of the Energy Institute. 89 (2016) 150-157.

DOI: 10.1016/j.joei.2015.01.001

[7] A. Parlak, The effect of heat transfer on performance of the diesel cycle and energy of the exhaust gas stream in a LHR diesel engine at the optimum injection timing, Energy Convers. Manag. 46 (2) (2005) 167-179.

DOI: 10.1016/j.enconman.2004.03.001

[8] H. Hazar, Effects of biodiesel on a low heat loss diesel engine, Renew. Energy 34 (6) (2009) 1533-1537.

DOI: 10.1016/j.renene.2008.11.008

[9] T. Hejwowski, A. Weronski, The effect of thermal barrier coatings on diesel engine performance, Vacuum. 65 (2002) 427-432.

DOI: 10.1016/s0042-207x(01)00452-3

[10] B. Istrate, C.I. Crimu, C. Munteanu, C. Biniuc, L.G. Pintilei, S.I. Strugaru, P. Avram, K. Earar, Structural modification of α-Ti based alloy after submission to open flame thermal shock, Key Engineering Materials. 638 (2015) 333-338.

DOI: 10.4028/www.scientific.net/kem.638.333