Choice of Protective Coating of Metal Molds for Casting Non-Ferrous Alloys

Abstract:

Features of the process of injection molding of non-ferrous metals and zinc alloys, in particular, consisting in the rate of crystallization of the process of melting, as well as cyclically repetitive temperature and shock loads of the forming surfaces of the mold, cause most defects, in which the form can be considered unfit for further use.

• Periodical: Solid State Phenomena (Volume 299)
• Pages: 867-871
• DOI: https://doi.org/10.4028/www.scientific.net/SSP.299.867
• Online since: January 2020
• Authors: Renat V. Gavariev*, Igor A. Savin, Elena N. Soldatkina
• Keywords: Casting, Compression Mold, Covering, Foundry

References

[1] R.V. Gavariev, I.A. Savin, I.O. Leushin, Impact of the functional coating on service durability of injection molds for the zinc alloys pressure casting. Tsvetnye Metally, 1 (2016) 66-70.

DOI: 10.17580/tsm.2016.01.11

[2] I.P. Balabanov, L.A. Simonova, O.N. Balabanova, Systematization of accuracy indices variance when modelling the forming external cylindrical turning process. IOP Conference Series: Materials Science and Engineering, 86 (1), (2015).

DOI: 10.1088/1757-899x/86/1/012010

[3] D.L. Pankratov, R.V. Gavariev, K.N. Gavarieva, Influence of multilayer coatings on the operational stability of molds for injection molding. IOP Conference Series: Materials Science and Engineering, Volume 134, Issue 1, 8 July (2016).

DOI: 10.1088/1757-899x/134/1/012031

[4] A. Shaparev, I. Savin, Calculation of the Amount of the Reduction Required for the Formation of Compound Layers during Cold Rolling of Bimetals. Materials Science Forum, Vol. 870, (2016), pp.328-333.

DOI: 10.4028/www.scientific.net/msf.870.328

[5] R.V. Gavariev, I.A. Savin, Improvement of surface quality of casting produced by casting under pressure. Solid State Phenomena, 2017, pp.988-993.

DOI: 10.4028/www.scientific.net/ssp.265.988

[6] A.V. Shaparev, I.A. Savin, Calculation of joint plastic deformation to form metal compound in cold condition Solid State Phenomena, 2017, pp.313-318.

DOI: 10.4028/www.scientific.net/ssp.265.313

[7] R.V. Gavariev, I. A. Savin, I.O. Leushin, Improvement of zinc castings surface quality by laminated protective coating. Tsvetnye Metally, 5 (2017) 84-88.

DOI: 10.17580/tsm.2017.05.13

[8] H. Çuvalci, H.S. Çelik, Investigation of the abrasive wear behaviour of ZA-27 alloy and CuSn10 bronze, Journal of Materials Science, 46 (14) (2011) 4850-4857.

DOI: 10.1007/s10853-011-5396-9

[9] P. Kapranos, D. Brabazon, S.P. Midson, S. Naher, T. Haga, Advanced casting methodologies: inert environment vacuum casting and solidification, die casting, compocasting, and roll casting, casting, semi-solid forming and hot metal forming, Comprehensive Materials Processing, vol. 5, 2014, pp.3-37.

DOI: 10.1016/b978-0-08-096532-1.00503-3

[10] A.P. Hekimoğlu, T. Savaşkan, Effects of Contact Pressure and Sliding Speed on the Unlubricated Friction and Wear Properties of Zn-15Al-3Cu-1Si Alloy, Tribology Transactions, 59 (6) (2016) 1114-1121.

DOI: 10.1080/10402004.2016.1141443

[11] N.N. Safronov, L.B. Mingaleeva, and I.A. Savin. Optimization of Charge Material Composition in Shs Process with Ferrosilide Fabrication from Gaseous Wastes of Metallurgical Production. Chernye Metally, 2 (2008) 53-59.

[12] K.N. Gavarieva, L.A. Simonova, D.L. Pankratov, R.V. Gavariev, Development of expert systems for modeling of technological process of pressure casting on the basis of artificial intelligence, IOP Conference Series Materials Science and Engineering, September 2017, Institute of Physics Publishing.

DOI: 10.1088/1757-899x/240/1/012019

[13] R.V. Gavariev, I.A. Savin, Research of the Mechanism of Destruction of Compression Molds for Casting under Pressure of Color Alloys, Solid State Phenomena, Vol. 284, 2018, pp.326-331.

DOI: 10.4028/www.scientific.net/ssp.284.326

[14] A.D. Jayal, F.Jr. Badurdeen, O.W. Dillon, I.S. Jawahir, Sustainable manufacturing: Modeling and optimization challenges at the product, process and system levels, CIRP Journal of Manufacturing Science and Technology, 2 (3) (2010) 144-152.

DOI: 10.1016/j.cirpj.2010.03.006

[15] D.A. Dornfeld, Moving towards green and sustainable manufacturing International Journal of Precision Engineering and Manufacturing - Green Technology, 1 (1) (2014) 63-66.

DOI: 10.1007/s40684-014-0010-7

[16] I.P. Balabanov, V.N. Gilman, T.S. Timofeeva, A.I. Faskhutdinov, Modeling of the cutting edge rounding influence on the tool life in processing a gear wheel by the Power Skiving method, International Journal of Engineering and Technology(UAE), (2018).

DOI: 10.14419/ijet.v7i4.7.20386

[17] K.N. Gavarieva, L.A. Simonova, D.L. Pankratov, V.G. Shibakov, R.V. Gavariev, Application of multi-agent system for control of parameters of precision stamping process of bevel gears, IOP Conference Series Materials Science and Engineering, 412 (2018).

DOI: 10.1088/1757-899x/412/1/012020

[18] E.S. Prusov, A.A. Panfilov, V.A. Kechin, Role of Powder Precursors in Production of Composite Alloys Using Liquid-Phase Methods, Russian Journal of Non-Ferrous Metals. Vol. 58 (3) (2017) 308-316.

DOI: 10.3103/s1067821217030154

[19] V.B. Deev, E.S. Prusov, A.I. Kutsenko, Theoretical and Experimental Evaluation of the Effectiveness of Aluminum Melt Treatment by Physical Methods, La Metallurgia Italiana, 2 (2018) 16-24.