Search results

The study aims to correlate the optoelectronic and structural properties of the coatings with their composition and microstructure.
Materials and Methods The support material used was heat-resistant steel 10CrMo9.10, which is a special alloy steel, also known under the number 1.7380.
International Journal of Surface Science and Engineering, 1(1), 38-61
Journal of Thermal Spray Technology, 11, 86-94
Journal of thermal spray technology, 19, 137-147

The selection of these materials, with the aim of the lowest possible mass of the sandwich composite at a constant bending stiffness, is displayed systematically within this work.
Within this work, a systematic material selection of the materials for the face sheet and core of sandwich structures is carried out with the aim to optimize the stiffness-to-weight ratio.
Both foam types were based on an aluminium alloy, the boundary densities were 10-25% for the closed-cell foam, and 7- 20% for the open-cell foam.
Yao, Diffusion bonding in fabrication of aluminum foam sandwich panels, Journal of Materials Processing Technology, 230:35-41, 2016 [14] M.
Koch, Manufacturing hybrid lightweight compounds of closed-cell aluminium foam and thermosoftening plastics in injection moulding processes, 58th IWK, Ilmenau Scientific Colloquium, Technische Universität Ilmenau, 2014 [15] D.

Owing to the impact-fusion coating manufacturing process, only ductile metals (Zn, Ag, Cu, Al, Ti, Nb, Mo, etc.), alloys (Ni-Cr, Cu-Al, Ni alloys, McrAlYs, etc.) and polymers can be sprayed.
These include pure metals (Ag, Al, Cu, Fe, Mo, Ta, Ti, Zn, etc.) low alloy steels, Ni-Cr alloys, Ni base superalloys, Stainless steel, Zn alloys, Al alloys, Cu alloys, MCrAlY, etc.
At last Fe-Al intermetallic compounds have been produced using a ball-milled metastable Fe-Al-WC powder, spraying it by cold spray and then annealing coatings at a temperature over 500°C to form Fe-Al intermetallic compounds.
� Self fluxing alloys: It results in rather dense and hard coatings [105-108].
These self-fluxing alloys can be reinforced with hard ceramic particles such as WC [109]

The design and manufacture of cermet-type composite materials aims to obtain materials with physical, mechanical, and chemical properties that are better than those of their component materials.
The phase corresponded to Grossite (CaAl2O7) is expected because, in the bibliography, it has been reported that due to the pressing process, there are zones with uniformity of quantities of CaCO3 and Al2O3 by which CaAl2O4 compounds already formed interact with zones rich in CaCO3 and form phases like the one reported in the work with a greater number of oxygen atoms. [6], [14].
Ortega-Avilés, Sea snail shells for synthesis of ceramic compounds reinforced with metallic oxide: Microstructural, mechanical, and electrical behavior, Mater Today Commun. 28(2021)
Prattis, Kinetic study of the thermal decomposition of calcium carbonate by isotermal methods of analysis, The European Journal of mineral Processing and Enviromental Protection. 1-2 (2001) 89–102
Zawrah, Improvement of wetability, sinterability, mechanical and electrical properties of Al2O3-Ni nanocomposites prepared by mechanical alloying, Ceram Int.43-4 (2017) 3576–3582

Goldsmith et.al [106] made an automated approach to filter out 4,000 solvent free structures out of a Cambridge Structure database of 600,000 + compounds for their porosity, surface area, and total theoretical H2 uptake for both gravimetric and volumetric values.
The wide variety of porous solids being tested for hydrogen storage was recently further enriched by reports on nanotubes made of inorganic compounds having a varied chemical composition [117] (e.g., BN, NiO and TiO2).
Alloys Compd. 404–406 (2005) 399-401
Alloys Compd. 446/447 (2007) 380-384
Alloys Compd. 379 (2004) 280-289

Aim at the above status, a novel high-efficiency and compact process to fabricate copper cladding aluminum wire is proposed by authors [12~14] .
The microstructure of aluminum core, the eutectic microstructure of Cu-Al alloy interlayer and the microstructure of copper cladding layer can be seen obviously.
Hung: Journal of Materials Processing Technology Vol. 104 (2000), p. 226 [8] H.J.
Kim: Journal of Material Processing Technology Vol. 67 (1997), p. 24 [9] H.J.
Kwonb: International Journal of Mechanical Sciences Vol. 44 (2002), p. 247 [11] C.G.

The yield of cross-linking is enhanced in the presence of polyunsaturated compounds, such as polyfunctional vinyl monomers.
Major advantages of radiation curing include reduction or elimination of volatile organic compounds (VOCs) and it is faster process than chemical curing.
Graft copolymers can be considered as polymeric alloys.
Chemical composition of the wastewater consists of organic dyes, surfactants and other organic compounds.
Table 5 summarizes the dose needful for removal of aromatic compounds from water.

The samples were produced either by wet lay-up or by press moulding of MgO thickened prepregs (similar to sheet moulding compound).
The following test matrix was used - 6 specimens were tested before treatment; - 18 specimens underwent ageing treatment according to ASTM G 36 standard (this environment provides an accelerated method of ranking the relative degree of stress-corrosion cracking susceptibility for stainless steels and related alloys in aqueous chloride-containing environments). 9 specimens underwent treatment with pH = 7 (Fig. 6a) in an aqueous solution with 42% MgCl2. 9 specimens underwent treatment with acidic pH7 (Fig. 6b) adding to the previous aqueous solution HNO3, (1.5 cm3 in volume at a concentration of 67%).
The tests of accelerated ageing and water absorption have evidenced the resistance of the material adopted to the aggressiveness of the marine atmosphere; in the realization of real prototypes it is previewed however the utilisation of waterproofing treatments on the exposed parts, to the aim to improve the mechanical property of the composite.
Olivari, Composite Boat Hulls with Bamboo Natural Fibres, International Journal Materials and Product Technology, 36, 1/4 (2009) 73-89

EDX usage aims to confirm the presence of zinc (Zn), oxygen (O), and gold (Au) in the ZnO/Au sample.
Ezati, Journal of Colloid and Interface Science 514, 70 (2018)
Dincer, International Journal of Hydrogen Energy 44, 2474 (2019)
Jorio, Journal of Alloys and Compounds 797, 1320 (2019)

The response of strength to current increasing is regular for the aluminum alloys [41].
Hot cracking or solidification cracking in HAZ were often observed in spot welded of magnesium alloys [4].
Journal- New York, vol. 78, no.
Demkin, “Dimensions of Initial Contact in Spot Welding of Light Alloys, Welding Production .,” Weld.
Journal-Including Weld.