Search results

The analysis of the results shows that the resistance of the structure to cavitation erosion is dependent on the type of alloy, the degree of brittle intermetallic compounds and the mechanical properties specific to toughness.
All the alloys show a structure with acicular precipitates and inclusions of intermetallic compounds of aluminum such as CuAl, MgSi, MgZn, etc., compounds on which the resistance to cavitation stresses depends, because they contribute to the decrease of the strength of the structure by weakening the bonds between the basic grains and by creating crack primers.
It can be seen that in alloys 5083 and 6082 the number and sizes of intermetallic compounds are greater than in alloys 2017 A and 7075.
The resistance to cavitational erosion of aluminium alloys in the laminated state, expressed by the values of the reference parameters Mmax and vs, is dependent on the degree of alloying, the type of the principal alloying chemical elements, the values of the mechanical properties, the intensity and the size of the brittle intermetallic compounds. 2.
Matthews: Cavitation erosion of aluminium alloys.

In connection with the above, the aim of our work is to study ternary compounds of the system that can be used to produce alumina cements.
Lapin [15] obtained the triple compound BaCaAl4O8 from slag formed during the smelting of aluminum-barium alloys.
Using this method, we calculated the electronegativity of compounds (ENsol.) as the geometric mean of the electronegativities of the elements that make up the compound.
Physico-mechanical properties of ternary compounds of the system CaO–BaO–Al2O3 Compound W/C The term of stiffening [hrs. - min.]
The binding properties of the synthesized ternary compounds and compositions of the system were evaluated.

The aim of the research was to develop an amorphous and microstructured layer on non-amorphous alloys by laser surface treatment.
The aim of the research was to produce an amorphous and microstructured layer on non-amorphous but amorphisable alloys by laser surface treatment because the mechanical properties between the layer and the substrate could better.
Experimental Materials and Methods Different alloys were used in the experiments.
[2] K Tomolya, D Janovszky, et al.: Consolidation of Cu58Zr42 amorphous-nanocrystalline powders by PM Journal of Alloys and Compounds, 536:(Sup1) (2012) pp.
Haa, et al.: Improvement in mechanical properties of a Zr-based bulk metallic glass by laser surface treatment, Journal of Alloys and Compounds 504S (2010) S45–S47

Cryorolling as one of SPD techniques is to roll the metal or alloys at cryogenic temperature.
This paper is aimed to compare the cryorolled Al-Cu-Mg alloy and room temperature rolled alloy.
Fig. 4 shows the BF TEM micrographs and corresponding SAD patterns of peak-aged Al-Cu-Mg alloys aged for 24h.
Jayaganthan, Effect of ageing on microstructure and mechanical properties of bulk, cryorolled, and room temperature rolled Al 7075 alloy, Journal of Alloys and Compounds. 509(2011) 9609-9616
Panigrahi, Microstructure and texture evolution in cryorolled Al 7075 alloy, Journal of Alloys and Compounds. 496 (2010) 183-188

The aim of this work is to investigate the optimum heat treatment for Al-5.7Si-2Cu-0.3Mg aluminium alloys and study its effect on microstructure, phase transformations, and hardness.
In both the as-cast and as-cast-T6 alloys Al, Si, Al2Cu, β-Al5FeSi, and Al5Cu2Mg8Si phases compound were detected clearly occurred.
Garcia, “Effect of solution time in T6 heat treatment on microstructure and hardness of a directionally solidified Al-Si-Cu alloy,” Journal of Alloys and Compounds, vol. 683, pp. 485–494, 2016
Choi et al., “The effects of cooling rate and heat treatment on mechanical and thermal characteristics of Al-Si-Cu-Mg foundry alloys,” Journal of Alloys and Compounds, vol. 617, pp. 654–659, 2014
Lee, “Effects of eutectic silicon particles on tensile properties and fracture toughness of A356 aluminum alloys fabricated by low-pressure-casting, casting-forging, and squeeze-casting processes,” Journal of Alloys and Compounds, vol. 461, no. 1–2, pp. 532–541, 2008

Few data can be found on 6xxx series, as 6061 or 6082 alloys [7, 9, 17-19].
Kapranos, Thixoforming 7075 aluminium alloys, Mater.
Lapkowski, Some studies regarding thixoforming of metal alloys, J. of Mat.
Kang, Study on the effects of the compression ratio and mushy zone heating on the thixotropic microstructure of AA 7075 aluminum alloy via SIMA process, J. of Alloys and Compounds Vol. 509-2 (2011), 402–408
Birol, Solid fraction analysis with DSC in semi-solid metal processing, Journal of Alloys and Compounds 486 (2009), 173–177

As a result of the addition of Co to the filler material, Co-compounds, CoTi, AlCo and CoO, were detected.
However, Ag does not react or form compounds with any of the elements in the sample. 3.
Again, CuO and AlCu compounds were formed.
X-ray diffraction also shows the formation of Co compounds, mainly CoTi, AlCo, and CoO.
Huang: Joining mechanism of Ti/Al dissimilar alloys during laser welding-brazing process, Journal of Alloys and Compounds 509 (2011) 891-898 [10] S.Y.

Divinski, Ni tracer diffusion in CoCrFeNi and CoCrFeMnNi high entropy alloys, Journal of Alloys and Compounds 688 (2016) 994-1001
Sohn, Composition-dependent interdiffusion coefficient, reduced elastic modulus and hardness in γ-, γ′-and β-phases in the Ni-Al system, Journal of Alloys and Compounds 727 (2017) 153-162
Yeh, Microstructure and mechanical property of as-cast, -homogenized, and -deformed AlxCoCrFeNi (0 ≤ x ≤ 2) high-entropy alloys, Journal of Alloys and Compounds 488 (2009) 57-64
Yeh, Interdiffusion in the fcc-structured Al-Co-Cr-Fe-Ni high entropy alloys: Experimental studies and numerical simulations, Journal of Alloys and Compounds 674 (2016) 455-462
Danielewski, Demystifying the sluggish diffusion effect in high entropy alloys, Journal of Alloys and Compounds 783 (2019) 193-207

Amount of compound distribute along grain boundary with composition of Al31.72Mg42.6Cu25.68, so it is suggested that the reaction happened between the particle and metrix alloy.
Elina＄Alloys and Compounds, Vol. 363(2004), p.154 [2] N.
Burkel, Alloys and Compounds, Vol. 434-435(2007), p.319 [6] P.D Bloom, J.W Andereq, V.
Kim, Alloys and Compounds, Vol. 342(2002),p.445 A.
Yuan, F.Y.Yan, M.Fang,The Chinese Journal of Nonferrous Metal, Vol. 11'4" (2001),p.571 [16] P.J.

Therefore, machining of titanium alloys is a high-cost process.
(a) Flank wear progression with cutting time (b) Tool life with hydrogen content Fig.3 Flank wear for all alloys Fig.3b shows the comparison of tool life for all titanium alloys.
Wang: Journal of Materials Processing Technology.
Yamane: Journal of Materials Processing Technology.
Lv : Journal of Alloys and Compounds Vol. 427(2007), p. 229.