Search results

Factors that affect Polymer Nanocomposites Structure 4.1.
The physical properties of nanocomposites depend greatly on the chemistry of polymer matrices, nature of nanofillers, and the way in which they are prepared.
TEM image shows three arm nanorods or tripods structure.
The ideal porous structure of anodic alumina is shown in figure 13 (b).
The inset of figure shows the structure of PVA:n-CdSe, based Schottky diode.

Nowadays these methods are widely used in different kind of science like physics, chemistry or engineering.
Such an internal structure is rather not meet in a nature.
The particles form the chain - like structure.
This kind of structure is rather not observed in real experiments.
O., Structure of the water: A Monte Carlo calculation, Chem.

Its use in the treatment of Luffa fibers has modified their internal structure, improved their mechanical properties, and enhanced their adhesion to cement.
These fibers have a naturally robust structure and offer exceptional insulation and absorption properties, while being environmentally friendly.
Wang, Advanced composite materials for structure strengthening and resilience improvement, Buildings, 13 (2023) p. 2406. [2] N.
Wang, Study of effect of fibre volume and dimension on mechanical, thermal, and water absorption behaviour of luffa reinforced epoxy composites, Advanced composite materials for structure strengthening and resilience improvement, Advanced composite materials for structure strengthening and resilience improvement (2012) pp. 5133–5151. [16] S.
Alencar et al., Feasibility study of incorporation of bamboo plant fibers in cement matrices, Sustainable Chemistry for the Environment 2 (2023)100020, p. 100020. [26] J.

The results indicated that certain structure of the iron oxide was an efficient catalyst for decolorization of organic compounds under UV irradiation and structure of iron oxide might play a very important role in iron oxide/H2O2 system.
This result certainly proved that the structure of iron oxide would affect the photochemical behavior in the system.
From the structure information of the dyes we may expected the adsorption of MO on the a-Fe2O3 may weaker than Direct Red 4BS as well as the photo reactive activity.
Electron on π-bond of benzene ring was attracted by SO3 or other bond and they blocked the electron transfer from a-Fe2O3 to the azo bond, which had electron-defect structure, this inevitably leading to non-bio-degradation.
Kiwi, Accelerated photobleaching of Orange II on novel (H5FeW12O4010H2O)/silica structured fabrics, Water Res., 38 (2004) 3541-3550

Structure-Property Relationships of Polymer- Grafted Nanospheres for Designing Advanced Nanocomposites.
Nano-Structures & Nano-Objects, pp 1-13
Composite Structures, pp 1-12 [23] C.H.
Composite Structures, Vol 176, pp 961-972
Journal of Materials Chemistry A, Vol 3 (4), pp 1442–1449

El Bouziani, Phase diagrams of a mixed-spin hexagonal Ising nanotube with core-shell structure, Chin.
Deviren, Nonequilibrium magnetic properties of the mixed spin (1/2, 1) Ising nanowire with core-shell structure, Phys.
Wang, Hysteresis behaviors in a ferrimagnetic Ising nanotube with hexagonal core-shell structure, Physica.
Wang, Hysteresis behaviors in a ferrimagnetic Ising nanotube with hexagonal core-shell structure, Physica.
Li, Dynamic magnetic properties of borophene nanoribbons with core-shell structure: Monte Carlo study, J.

ANNs Sample was trained 20 times and tested 5 times without excluding any result with total number 25 run using network structure 6-3-1.
[24] Ellis, T., Chemistry of wastewater.
Arabian Journal of Chemistry, 2019. 12(8): p. 4897-4919

The experimental results show that the downward particle velocity distributes uniformly along the radius in the four regions, but the radial distributions of upward particle velocity and time-averaged particle velocity are core-annulus or heterogeneous structure in the three regions (distributor affect region, draft tube, gas-solid diffluence region), which have the common feature of aggregative fluidization occurred in normal fluidized beds.
Introduction As an effective multiphase flow reaction device, air-lift loop reactor (ALR) is widely used in many industrial processes for instance petrochemical, biochemical, environmental science and engineering chemistry of metallurgy, with its inherent advantages such as high gas holdup, high mass transfer rate, sufficient interphase contact and simple structure.
In conclusion, the above factors explain the reason the radial distributions of uu and um display a core-annulus structure in the draft tube.
The radial distributions of uu and um display a core-annulus heterogeneous structure，meanwhile, the radial distribution of ud is relative uniform in the three region (the distributor affect region, the draft tube and the gas-solid diffluence region), yet a relative homogenous radial distribution of um in the annulus in GSALR.

Besides, it is found that the Ti4O7 powders obtained by titanium thermal reduction method exhibited the crystal structure, distinctly possessing an average particle size around 750 nm.
This unique structure endows Magnéli phases with metal–non metal transitions speciality, showing super electrical conductivity, great corrosion resistance, and outstanding thermal stability [4-6].
SEM image obviously show the crystal structure distinctly and their average particle size is around 750 nm.
West, Handbook of Chemistry and Physics, New York 1987
Hyde, Crystallographic shear in the higher titanium oxides: Structure, texture, mechanisms and thermodynamics, Prog.

Polymers are widely used to produce components from prototypes to functional structures with complex geometries [29].
Greguric et al. used a carbon-fiber reinforcement and printed aluminum rods by means of a rapid prototyping tool process to restore old automotive structure with a similar honeycomb structure that increases its strength [86].
Li, Metal-Based 3D-Printed Micro Parts & Structures, Reference Module in Materials Science and Materials Engineering, Elsevier, 2020, ISBN 9780128035818, https://doi.org/10.1016/B978-0-12-819726-4.00009-0
Li, S-J Park, Synthesis and application of epoxy resins: A review, Journal of Industrial and Engineering Chemistry (2015) 29, 1–11, https://doi.org/10.1016/j.jiec.2015.03.026
Krijnen, Embedded sensing: Integrating sensors in 3D printed structures.