Search results

When the first impermeability data is taken down, the water pressure continues to be raised until the six specimens are all permeable and the first impermeability experiment ends.
The experiment data is shown in Table 5.
Therefore, when the mortar matrix is mixed with two materials, fibers not only have the ability of crack resistance, brittle reduction and shrinkage resistance, but also provide a basis for the better performance of SJ material’ properties, enabling the mortar matrix to own properties of high crack resistance and high impermeability.

Tosun et al. [2006], Drilling of Al/SiCp Metal Matrix Composites in which Surface roughness, flank wear reduction by taguchi technique by Gul Tosum & Mehtap Muatoglu [2003] investigated the effect of the various cutting parameters on the surface quality and microstructure on drilling of Al/17% SiC particulate MMC by using various drills.
In the grey relational analysis, data processing is first performed in order to normalize the raw data for the analysis.

For instance, a significant reduction in stiffness resulting from introduction of a crack will cause detectable changes in the modal parameters, see e.g. [5,27].
Fernando, Structural Integrity Evaluation of Wind Turbine Blades Using Pattern Recognition Analysis on Acoustic Emission Data, Proceedings, 25th European Conference on Acoustic Emission Testing, 2002
Zadoks, Application of Damage Detection Techniques using Wind Turbine Modal Data, SAND98-2823c, Sandia National Laboratories, 1998

With the sintering process, the sample suffers a compaction, like a reduction in their dimensions, in addition to the loss of mass described above, a behavior that affects the volumetric density of the samples.
This decrease is related to the increase in the addition percentage, according to data in article [16].
Fracture toughness results of the samples (the figures indicate the different models used for data processing).

The images for the polished Si wafer in Fig. 4 are obtained from reference data.
The image for the polished Si wafer in Fig. 6(i) is obtained from reference data.
The reconstructed surfaces are unaffected by a reduction in the unloading temperature.

Experimental testing of the RSFJ with the secondary fuse Secondary fuse is activated Reduction in FRSFJ,slip Analytical Experimental kRSFJ,fuse (a) (b) Fig. 5.
It can be seen that the analytically calculated effective stiffness of the RSFJ after locking perfectly matches with the experimental data.
The data in Fig.8 suggests that having RSFJs in the roof has a minor effect on the base shear and the maximum inter-story drift.

Line 01 (115.4,y,75) Figure4 – Velocity data location used for validation.
As the critical void regions are located at the ends of the mold and that increased resin inlet flowrate causes a reduction in voids within the mold, was applied the method proposed by Lee et al. [26], using different injection points, in order to reduce the voids at the mold ends in the short period of time the idea is to obtain good finish quality of the composite after injection progress.
From the data obtained, although the injection configuration is different for the three cases, the total resin mass flowrate is the same in each case, and the resin and air volume fraction curves are practically the same.

This deterioration is represented in the model as a reduction of capacities of production lines.
Numerical Example A part of our data is based on the numerical example used in [7, 13].We define a planning horizon containing 8 basic production periods such that.
Table 2: Production data Product/ Period Producing cost Launching cost Storing cost Breaking cost Fixed needs Variable needs i={1,2} t={1,…,8} 5 25 2 100 5 1 On the other hand, we assume that the system lifetime is distributed according to the Gamma distribution with the parameters.

Analysis of data in Figure 3.
The data results in Figure 3.
The time from 1 hour to 2 hours is the time for enzymes to catalyze and release compounds in the juice, so the vitamin C content also increases, the hydrolysis time still prolongs the values ​​will be consumed so there is a sign of reduction.

According to the data obtained, in the case of filling the PPS matrix with industrial glass fibers not treated with coupling agents, destruction is observed near the fiber surface; for fibers treated with γ-aminopropyltriethoxysilane, interfacial adhesion between the fiber and PPS is observed.
The functionalized polymer is obtained by treating PPS with a mixture of nitric and sulfuric acids, followed by reduction of the nitro to amino group according to the following scheme [44–46]: PPS containing side amino groups can also be synthesized by the method of nucleophilic substitution in the medium of N-methylpyrrolidone under pressure [47].
The data obtained are confirmed by SEM micrographs (Fig. 3).