Search results

From this data, it can be inferred that using immiscible polymer blend promoted segregation of conductive particles into a confined volume, leading to more conducting pathways.
Hence, reduction in thickness of graphite platelets will result in larger specific surface area and higher aspect ratio.

Macromolecules comprising anticancer receptors MMP9, MMP2, CCNA2, P53, and BAK, EGFR, ADPRP (PDB ID: 4H1Q, 3AYU, 2V22, 2VUK, 6UXM, 1U0K, 5HG7 respectively) were retrieved from the Protein Data Bank (PDB).
Lockhart et al., Reduction of wound angiogenesis in patients treated with BMS-275291, a broad spectrum matrix metalloproteinase inhibitor.

Adding anthraquinone into the soda pulp led to an increase in screen pulp yield, a lower lignin content, increase energy efficiency, and a reduction in rejects [23, 26, 27].
This graphical figured out the data values in table 1 for different biomass resource (banana pseudo stem, wheat straw, eucalyptus labill, Enset Ventricosum stem and bagasse).

Concerning the empirical modelling, the authors analyze the models developed in Australia and Canada since the 1960’s and 1920’s respectively in the different type of ecosystems concerned by wildland fire (grassland, eucalypt stands, moorlands and shrublands) The researcher focus their attention to the required input data of these empirical models and the empirical functional relationships established between intrinsic parameters of vegetation and wind or slope effects on wildland fire dynamic.
The reduction of fuel can be accomplished using mechanical means (bulldozer) or using a suppression fire (also called a counter fire or a backfire), by burn-out operations and back-firing operations.

The path slope at the ZFP in Eq. (10) can also be related to atomic mobilities of the components and thermodynamic data for the system [33].
The morphological separation of phases occurs with appreciable reduction of interfacial boundaries of the original two-phase alloys.

The reduction of electromagnetic backscattering using the microwave absorbing materials therefore has important implications in the field of electromagnetic compatibility.
W-type hexaferrite is a very useful material for home appliances, electronic products, communication equipments, permanent magnets, recording heads, bubble domain memories, components in high-frequency microwave devices and data processing devices due to its unique electrical and magnetic properties [35–39].
Powder-X software has been used and after indexing on standard XRD data, experimental spectra show that there is no other phase in the composite samples, except for Y-type hexaferrite.

Then, a four high pilot cold rolling mill was used to cold-roll the hot-rolled strips to the final thickness of 0.5 mm with a total reduction of 81%.
Fig. 3 Number density and size distribution of non-metallic inclusions with different RE contents in the slabs The statistical datum shows number density of the inclusions in the inner samples which size is in the range of 0.05μm~1.0μm are 33×104 /mm3 and 17.5×104 /mm3 when the content of RE in the steel bearing 1.15 wt% Si is 60×10-4 wt% and 100×10-4 wt% respectively.

Gap control In order to derive the system’s equation, the following symbols are used: - s = Position of edge of exotic material (mm) relative to pre-erosion datum - A = Cross sectional area of PCD (mm2) - = Mass removal rate (kg/s) - r = Density of exotic material (kg/mm3) - e = Gap (mm) - f = Actual feedrate (mm/s) - V= Average gap voltage (V) From Fig. 2, the mass removal rate is measured by the movement of the edge of the exotic material: (1) (2) (3) Where f is the feedrate function depending on gap voltage.
It is therefore important to monitor the reduction in dielectric strength of the oil to ensure that experimental results take into account this variable.

It is expressed as a percentage reduction in pregnancy rate for a single use of emergency contraception.
[5] http://www.searo.who.int/entity/health_situation_trends/data/mnch_unmet-needs-of contraceptives / en/

Device degradation from storage tests conducted in this manner is characterized by a reduction in the amount of current for a given voltage or equivalently, a higher voltage requirement for a given current density.
A linked computer interface was used to record Load and displacement data up to the point of interfacial separation/failure of the interface by using a linked computer interface.