Search results

Therefore, defect engineering may be used for the processing of TiO2-based oxide semiconductors, which exhibit properties that are critical for photoreactivity.
Several unresolved problems will be discussed and the key questions, that need to be addressed, will be formulated.
Therefore, appropriate engineering is required to increase the reactivity of the cathodic sites.
Therefore, the photocatalytic systems may be optimised by using defect engineering, which allows to achieve the desired properties by imposition of controlled defect disorder.
C Vol. 112 (2008) p. 602 [37] International Organization for Standardization: Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for antibacterial activity of semiconducting photocatalytic materials (ISO 27447:2009) [38] T.N.

Meanwhile, it shall also coordinate the exchanging of materials between the environment and the system.
Therefore, additional emergency engineering measures should be taken in the raw water system.
Engineering Science, 2001, (08). ( In Chinese) [4] ong Chun-sheng, Huang Qiang, Liu Jun-ping, Liu Han.
Journal of Systems Engineering, 2005, 20(6): 613-619. ( In Chinese) [13] Zhang Jun-yan.
Systems Engineering-theory & Practice, 2005, (03). ( In Chinese)

Advanced Materials, 21 (2009) 4565-4583
Materials Science and Engineering: B, 213 (2016) 12-40
High-purity semiconducting single-walled carbon nanotubes: a key enabling material in emerging electronics.
Computational materials science, 82 (2014) 159-164
Materials Today: Proceedings, 3 (2016) 1820-1827

The SiC additions also aid in processing of the materials by reducing the maximum temperature required to densify the materials, and by reducing the growth of the ZrB2 grains [10].
Raw Materials and Processing.
Ellerby: Key Eng.
Peters: Airforce Materials Laboratory Technical Report AFML-TR-68-190, Wright-Patterson Airforce Materials Laboratory, Dayton, OH, USA (1968)
Takagi, in: Handbook of Ceramic Hard Materials, edited by R.

The semiapex angle determines the representative engineering strain associated with the indentation.
Then, if slip occurs on the circles, the material under the indenter is lowered uniformly, whereas material outside the zone of contact is raised as indicated by the dashed lines.
There is another key ingredient: the slip-circle construction permits sharp discontinuities in dislocation density and hence in the flow stress as a function of position.
The increment in primary shear stress per unit engineering primary shear strain is the rate of work-hardening, rwh.
Calladine: Engineering Plasticity (Pergamon Press, Oxford and New York 1969) [16] J.

Prior to measurement, the catalyst materials were dispersed in ethanol, deposited onto 300 mesh carbon-coated grids, and subsequently dried.
Beilis, Plasma engineering: applications from aerospace to bio and nanotechnology, 2nd ed.
Glarborg, “The NH3/NO2/O2 system: Constraining key steps in ammonia ignition and N2O formation,” Combust.
Kennedy, Plasma Physics and Engineering, 2nd ed.
Zhu, “Control of ammonia escape from SNCR flue gas denitrification of circulating fluidized bed boilers in coal-fired power plants,” in 2022 9th International Forum on Electrical Engineering and Automation (IFEEA), 2022, pp. 770–773. doi: 10.1109/IFEEA57288.2022.10038116

Effect of Device Parameters on Carbon Nanotube Field Effect Transistor in Nanometer Regime Sanjeet Kumar Sinha1,a and Saurabh Chaudhury2,b 1,2Department of Electrical Engineering, NIT Silchar,Assam-788010, India.
CNT’s have unique properties such as stiffness, strength, and tenacity compared to other materials especially to silicon [13].
Polysilicon have been utilized as gate materials since the evolution of MOSFET device.
Drain current vs. drain voltage for different High-K materials Drain voltage at fixed drain current for different High-K materials are shown in plot of Fig.8.
Effect of Channel Length Channel length is key parameter in MOSFET devices.

Wang, Preparations and Applications of Zinc Oxide Based Photocatalytic Materials, Advanced Sensor and Energy Materials
Jaffar, Green Synthesis of Zno and Mg Doped Zno Nanoparticles, and Its Optical Properties, Journal of Materials Science: Materials in Electronics. 28 (2017) 7677-7685
Sonawane, Synthesis of Cu Doped Zno Nanoparticles: Crystallographic, Optical, Ftir, Morphological and Photocatalytic Study, Journal of Materials Science and Chemical Engineering. 3 (2015) 39-51
Perng, Defect Engineering of Zno: Review on Oxygen and Zinc Vacancies, Journal of the European Ceramic Society. 41 (2021) 4977-4996
Singhal, The Study of Optical, Structural and Magnetic Properties of Cu-Doped Zno Nanoparticles, Journal of Materials Science: Materials in Electronics. 34 (2023) 288

A Study of the Preparation and Properties of the Concrete for the Bearing Platform of the Xiamen-Zhangzhou Sea-spanning Bridge Hongmei Hu1,a Hao Wang1,b Ronggui Du1 Boshen Zheng1 Yunkun Yi2 Yawen Shen1 1School of architecture and Civil Engineering,Xiamen university,Xiamen,China 2Fujian Xiamen-Zhangzhou Bridge Co.
Materials and Structures . 2007 ,38(5):481-496
(in chinese) [4] Hongmei Hu,Baoguo Ma.Binding Capability of Mineral Functional Materials with Chloride Ion.
[J].Journal of building materials,2004,7(4):406-410.
(in chinese) [5] Hongmei Hu,Shaoyin Zeng,Binbin Yu.Research on Relationship Between the Strength Class of Merchandise Concrete and Chloride Ion Diffusion Coefficient[J].Fujian Building Materials,2011, (1):1-4.

Ductile Fracture in Metal Forming: A Review of Selected Issues Sergei Alexandrov1,2a , and Elena Lyamina2b 1National Chung Cheng University, Department of Mechanical Engineering and Advanced Institute for Manufacturing with High-tech Innovations, 168 University Road, Ming-Hsiung, 62102 Chia-Yi, Taiwan 2A.
Therefore, applying the associated flow rule leads to plastically incompressible materials.
Equation (12) is also valid for a class of viscoplastic materials [14].
It is very similar to the mechanics of cracks where fracture conditions from the strength of materials cannot be used for cracked bodies because stress components approach infinity near the crack tip (for example, [24]).
Lyamina, Singular solutions for plane plastic flow of pressure-dependent materials, Dokl.