Search results

Research on the Relation of Brands Image to Product Form Wang Yanqun1, Zhang Bingchen 1,2 ,Guo Weimin2 1Department of Industry Design, Hunan University of Science and Technology, Xiangtan City, P.R.
The mainly form features of product may be different because of different function, but the form style and sense of material can be unified.
Brand-Oriented Product Desig, Journal of Southern Yangtze, 2005(4)

Khan3,d 1: Department of Chemistry, Faculty of sciences, Tlemcen university, Algeria 2: Chemist Director, Department of hydraulics, faculty of Technology, Tlemcen university, Algeria 3: Laboratory of Coordination Chemistry, Faculty of Pharmacy, Angers University, France.
Material: The absorption measurements were performed using a spectrophotometer Vis (400-800 nm) Jasco V-570 Ubest at 25° C.
Zurowska, Journal of Solution Chem.

Another aim of the present study is to analysis the distributions and species of nitrogen compounds in feedstock Material and experiments Properties of feedstock and catalyst.
Acknowledgements Authors are grateful for financial support from the Taishan Scholar Constructive Engineering Foundation of Shandong province (No.ts20120518), the supported from Science Foundation of China University of Petroleum, Beijing (No.KYJJ2012-06-32), and supported by Major State Basic Research Development Program (No.sq2013CB081304).
[7] Hang Yu, Shuyuan Li and Guangzhou Jin, Journal of Fuel Chemistry and Technology. 38(2010) 297–301, in Chinese.

Then using the elastic modulus E and Poisson ratio of the device material, the maximum and minimum positive stresses on the test points can be obtained: (3) Furthermore, according to the fourth strength theory, the equivalent stress of the test points can be obtained: (4) Figure 2 describes the equivalent stress spectrum of points 1~8 under No. 13 digging condition.
[8] Luigi Solazzi, Design of aluminium boom and arm for an excavator, Journal of Terramechanics, 47 (2010) 201-207
[9] Guojun Chen, Hydraulic Excavator, WuHan：Huazhong University of Science and Technology Press, (2011) 137-158.

Whereas the relative contribution of white noise may be traced to material fracture caused by built-up edge or the general worsening of the machine condition.
This work is partly supported by the science and technology major project of China (No. 2012ZX04012031).
Bhuiyan, etc: EURASIP Journal on Advances in Signal Processing, 2008, doi:10.1155/2008/728356 [11] Hardy, R.L: J Geophys Res, Vol. 76 (1971), p.1905

Apart from LFW data set, we also use the large photos presented on Zhu’s home page as the experimental material.
Acknowledgements This work was supported by the National Natural Science Foundation of China (Grant No. 61101152).
International Journal of Computer Vision 2004

Piezo resistive acceleration sensors use material strain of the seismic mass to detect the deflection.
In: International Journal of Manufacturing Research.
Springer Science + Business Media, 2011

But the material is too expensive to use in developing country for its difficult regeneration and poor mechanical rigidity [2, 6].
Materials and Methods Materials.
This research was funded by the National Nature Science Fund for Distinguished Young Scientists (Grant No. 50825802) and the Key Subject of National Natural Science (Grant No. 50938004) and Jiangsu Nature Science Fund For Distinguished Scientists (Grant No.
Ferro-Garcia, Journal of Chemical Technology and Biotechnology 84 (2009), p. 367 [23] D.

Nanotechnology exploits current progress in physics, materials science, chemistry and biotechnology to form novel materials that have unique properties significantly different from their bulk counterparts.
In physics and material science, nanoscience is most often associated with the behaviour of electrons and photons in nanoscale region.
From the past two decades, enormous efforts have been made to synthesize and characterize semiconductor materials of group II-VI, III-V, III-VI, and oxide-semiconductor materials.
The materials having no dimensions in the nano-scale region include bulk materials.
Tiwary, Microwave assisted synthesis of CdS nanoparticles for structural and optical Characterization, International Journal of Innovative Research in Science, Engineering and Technology, 3 (2014) 10670-10674

Branze 38, 25123 Brescia, Italy 2School of Chemical Engineering, College of Engineering and Physical Sciences, University of Birmingham, Edgbaston, UK.
For the metallic materials, Powder Bed Fusion (PBF) technologies can be used, classified in two sub-categories, according to the source of energy used: laser or electron beam.
Materials and Methods Fabrication and methodology In this work, Ti-6Al-4V powder was chosen to produce cubic lattice structures.
Birbilis, “Additive Manufacturing of Titanium Alloys for Orthopedic Applications: A Materials Science Viewpoint,” Adv.
Attanasio, “An experimental study on micro-milling of a medical grade Co-Cr-Mo alloy produced by selective laser melting,” Materials (Basel)., vol. 12, no. 13, 2019, doi: 10.3390/ma12132208