Hot Deformation Behavior and Stability Criteria of WE54 Magnesium Alloy

Abstract:

A precise description of the hot deformation behavior as well as determination of the stability conditions as influenced by temperature and strain rate is fundamental for the simulation of metal forming processes. In this work, a revision of various stability criteria of magnesium alloy WE54 is conducted. The study corresponds to own work and that of Lentz et al. and is based on compression tests at high temperature and high strain rates. Stability and processing maps were obtained using a variety of stability criteria, some based on the efficiency parameter η and others on the strain rate sensitivity parameter, m. This parameter is usually determined by fitting the curves strain rate, ε, versus stress, σ, by means of a potential equation named “power law” or by a polynomial of second or third degree, and calculating the slope of the logarithmic curve at each point using successive derivatives. This procedure is compared with one developed by us where all experimental points are fitted to a single hyperbolic sine equation of Garofalo type and then m and η are calculated for each ε and T using this equation. The maps obtained by one or the other method differ considerably. The predictions of these maps were contrasted with microstructural observations and conclusions on the deformation behavior of the alloy are reached.

• Periodical: Materials Science Forum (Volume 879)
• Pages: 1618-1623
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.879.1618
• Online since: November 2016
• Authors: Ignacio Rieiro, Manuel Carsí, Oscar Ruano*
• Keywords: Constitutive Equations, Dynamic Material Model, Garofalo Equation, Hot Forming, Magnesium Alloy WE54, Stability Maps

References

[1] Y.V.R.K. Prasad, H.L. Gegel, S.M. Doraivelu, J.C. Malas, J.T. Morgen, K.A. Lark, D.R. Barker, Metall. Trans. A 15 (1984) 1883.

[2] P.E. Wellstead, Introduction to Physical System Modelling, Academic Press, (1979).

[3] H.L. Gegel, J.C. Malas, S.M. Doraivelu, V.A. Shende, Metals Handbook, vol. 14, ASM, Metals Park, 1987, p.417.

[4] J.C. Malas, V. Seetharaman: JOM 44 (1992) 8.

[5] J. C. Malas III, PhD Thesis, Ohio University, (1991).

[6] J.M. Alexander: Modelling Hot Deformation of Steels, J.G. Lenard (Ed. ), Springer-Verlag, Berlin, 1989, p.101.

[7] H. Ziegler, in: Progress in Solid Mechanics, vol. 4, Wiley, NY, 1965, p.191.

[8] A.K.S. Kumar, MS Thesis, Indian Institute of Science, Bangalore, India (1987).

[9] M. Carsi, M.J. Bartolomé, I. Rieiro, F. Peñalba, O.A. Ruano, Mater. Design 58 (2014) 30-35.

[10] M. Lentz, S. Gall, F. Schmack, H.M. Mayer, W. Reimers, J. Mater. Sci. 49 (2014) 1121-1129.

[11] Y.V.R.K. Prasad, K.P. Rao: Mater. Sci. Eng. A 391 (2005) 141.

[12] P.V. Sivaprasad, S. Vegunopal, S. Vegunopal, V. Maduraimuthu, M. Vasudivan, S.L. Mannan, Y.V.R.K. Prasad, R.C. Chaturvedi: J. Mater. Sci. Technol. 132 (2003) 262.

[13] I. Rieiro, M. Carsí, O.A. Ruano, Mater. Sci. Technol. 25 (2009) 995.

[14] I. Rieiro, O.A. Ruano, M. Eddahbi, M. Carsí, J. Mater. Proc. Technol. 78 (1998) 177.