Materials Science Forum

ISSN: 1662-9752

Main Themes

Volumes
Edited by: B. Mishra, M. Ionescu and T. Chandra
Online since: May 2014
Description: Collection of selected, peer reviewed papers from THERMEC 2013, 8th International Conference on PROCESSING & MANUFACTURING OF ADVANCED MATERIALS Processing, Fabrication, Properties, Applications, December 2-6, 2013, Las Vegas, USA.
The 470 papers are grouped as follows:
Chapter 1: Al Alloys,
Chapter 2: Mg Alloys (Prof Karl U. Kainer Symposium),
Chapter 3: Ti Alloys/ Aerospace Structural Metallic Materials,
Chapter 4: Steels,
Chapter 5: TMP Microalloyed Steels (Prof. A. J. DeArdo Symposium),
Chapter 6: High & Ultra High Temperature Materials,
Chapter 7: Bio Materials,
Chapter 8: Advanced Protective Coatings/Surface Engineering,
Chapter 9: Composites (MMC, CMC)/ Nanocomposites/ Synthetic & Foams),
Chapter 10: Interfaces & Grain Boundaries,
Chapter 11: Fuel Cells, Hydrogen Storage Technologies, Batteries, Supercapacitors & Thermoelectric Materials,
Chapter 12: Friction Stir Processing/Welding,
Chapter 13: Materials Under Extreme Conditions,
Chapter 14: Metallic Glasses/ Bulk Metallic Amorphous Materials,
Chapter 15: Nanomaterials for Structural & Energy Applications,
Chapter 16: Neutron Scattering & X-Ray Studies of Advanced Materials,
Chapter 17: Modelling & Simulation,
Chapter 18: Materials Performance,
Chapter 19: Smart/Intelligent Materials & Processes,
Chapter 20: Texture of Materials (Prof. G. Gottstein Symposium),
Chapter 21: Ultra-Fine – Grained Materials (Prof. T. G. Langdon Symposium),
Chapter 22: Welding & Joining of Advanced and Special Materials

783-786

Edited by: Margita Longauerová and Pavol Zubko
Online since: April 2014
Description: Collection of selected, peer reviewed papers from the the International Symposium on Metallography (Metallography 2013), April 24–26, 2013, Stará Lesná, Slovak Republic.
Volume is indexed by Thomson Reuters CPCI-S (WoS).
The 123 papers are grouped as follows: Invited Lectures,
I. Prediction, Process Simulation and Metallographic Methods,
II. Solidification and Solid State Transformation, III. Welding,
IV. Interrelationship between Microstructure and Material Properties,
V. Fractures, Defects and Material Degradation, VI. Fatigue and Creep,
VII. Nonferrous Alloys,
VIII. Powder Metallurgy, Composites, Ceramics, Superconductors and Metallic Glasses,
IX. Coatings and Nanomaterials,
X. Metallography in Archaeology (Archaeometallurgy)

782

Edited by: Alagarsamy Pandikumar, Huang Nay Ming and Rajendran Jothilakshmi
Online since: March 2014
Description: Volume is indexed by Thomson Reuters BCI (WoS).
The multi-functional properties of nanomaterials offer a wide range of opportunities for addressing several research and development challenges in the area of nanoscience and nanotechnology. Multi-functional nanomaterials find wide application in a variety of sectors including agriculture, medicine, telecommunications, disaster management and environmental conservation.The focus of this special topic volume is on multifunctional nanomaterial development and their emerging applications towards commercialization. This special topic illustrates a new pathway to achieve novel practical applications using nanomaterials. This special topic can be utilized as a text for researchers as well as graduate students who are interested in nanomaterials based applications. This special topic volume is multidisciplinary by nature. The readers can acquire the necessary knowledge in physics, chemistry and biology related to these multifunctional applications which are associated with the emerging nanomaterials.

781

Edited by: Hajime Okumura, Hiroshi Harima, Tsunenobu Kimoto, Masahiro Yoshimoto, Heiji Watanabe, Tomoaki Hatayama, Hideharu Matsuura, Tsuyoshi Funaki and Yasuhisa Sano
Online since: February 2014
Description: The papers cover most of the current research efforts on the wide bandgap semiconductor silicon carbide (SiC) and related materials, and a wide range of topics from crystal growth to their power electronics applications. In these proceedings, the written version of 270 contributed papers and 13 invited papers are included. The major chapters of the proceedings collect papers in the area of bulk growth of SiC, epitaxial growth of SiC, physical properties and characterization, processing, devices and application. There are three shorter chapters on graphene, III-nitrides and related materials.
Volume is indexed by Thomson Reuters CPCI-S (WoS).
The 283 papers are grouped as follows:
Chapter 1: SiC Bulk Growth;
Chapter 2: SiC Epitaxial Growth;
Chapter 3: Physical Properties and Characterization of SiC;
Chapter 4: Processing of SiC;
Chapter 5: Devices and Circuits;
Chapter 6: Related Materials.

778-780

Edited by: Thomas Holden, Ondrej Muránsky and Cory J. Hamelin
Online since: February 2014
Description: Volume is indexed by Thomson Reuters CPCI-S (WoS).
The collection shows the importance of neutron and synchrotron radiation in the evaluation of mechanical stresses. It gathers the current knowledge from those concerned with the mechanical stress evaluation of materials and components using neutron and synchrotron radiation. It also gives an interesting "snap-shot" of progress in the field. The wide array contributions focus on the following key topics: Stress evaluation using neutrons, synchrotron radiation and X-rays; Development of measurement methods and instrumentation; Material processing and residual stresses; The influence of residual stresses on the physical and mechanical properties of materials and components; Measurement and assessment of residual micro-stresses and intergranular stresses; Residual strains and stresses in complex materials (e.g. multi-phase and biomaterials); Industrial applications of residual stress analysis using neutrons, synchrotron radiation and X-rays; and Complementary techniques for residual stress measurements.

777

Edited by: Dachamir Hotza and Antonio Pedro Novaes de Oliveira
Online since: January 2014
Description: Collection of selected, peer reviewed papers from the 20th Brazilian Conference on Materials Science and Engineering (CBECIMAT), November 4-8, 2012, Joinville, Santa Catarina.
Volume is indexed by Thomson Reuters CPCI-S (WoS).
The 132 papers are grouped as follows:
Chapter 1: Biomaterials;
Chapter 2: Materials Characterization;
Chapter 3: Modeling;
Chapter 4: Cements;
Chapter 5: Materials Degradetion;
Chapter 6: Ecological Materials;
Chapter 7: Surface Engineering;
Chapter 8: Materials Science and Engineering;
Chapter 9: Electrical Electronics and Optical Materials;
Chapter 10: Magnetic Materials;
Chapter 11: Nanostructured Materials;
Chapter 12: Materials Power Generation;
Chapter 13: Processing;
Chapter 14: Mechanical Properties;
Chapter 15: Recycling;
Chapter 16: Synthesis;
Chapter 17: Micellaneous

775-776

Edited by: A. Kiet Tieu, Hongtao Zhu and Qiang Zhu
Online since: November 2013
Description: Collection of selected, peer reviewed papers from the 15th International Conference on Advances in Materials and Processing Technologies (AMPT 2012), September 23-26, 2012, Wollongong, Australia.
Volume is indexed by Thomson Reuters CPCI-S (WoS).
The 108 papers are grouped as follows:
Chapter 1: Computer Aided Engineering;
Chapter 2: Deformation Process;
Chapter 3: Materials;
Chapter 4: Materials Removal Processes;
Chapter 5: Processing of New and Advanced Materials;
Chapter 6: Surface Engineering;
Chapter 7: Precision Engineering;
Chapter 8: Welding;
Chapter 9: Other Related Processes.

773-774

Edited by: H.G. Brokmeier, M. Müller, P.K. Pranzas, A. Schreyer and P. Staron
Online since: November 2013
Description: Volume is indexed by Thomson Reuters CPCI-S (WoS).
The exciting and comprehensive program of the MECA SENS VI conference provided a platform for current topics within the research fields of Mechanical Stress Evaluation with Neutrons and Synchrotron Radiation. The resulting contributions in this volume offer an excellent overview of all the various aspects in this field ranging from fundamental research and modelling to practical engineering applications.

772

Edited by: Alagarsamy Pandikumar and R. Jothilakshmi
Online since: October 2013
Description: Volume is indexed by Thomson Reuters BCI (WoS).
The development of photovoltaic technology is expected to solve problems related to energy shortages and environmental pollution caused by the use of fossil fuels. Dye-sensitizedsolar cells (DSSCs) are promising next-generation alternatives to conventional silicon-based photovoltaic devices owing to their low manufacturing cost and potentially high conversion efficiency. This special topic volume addresses recent advances in the research on dye-sensitized solar cells. The focus of this special topic volume is on materials development (sensitizers, nanostructured oxide films, and electrolyte), but commercialization. This work illustrates a new pathway to achieve highly efficient DSSCs for practical applications.

771

Edited by: Rupeng Zhu, Ning He, Yucan Fu and Changyong Yang
Online since: October 2013
Description: The papers in this special volume represent the latest development in the field of materials manufacturing technology, spanning from the fundamentals to new technology and applications. Especially, the papers cover the topics of advanced manufacturing technology and equipment, material forming science and technology, digital manufacturing system and management, modern design theory and methodology, and MEMS and ultra precision manufacturing.
Volume is indexed by Thomson Reuters CPCI-S (WoS).

770

Showing 111 to 120 of 482 Main Themes