Search results

Table 1.
Fig.1.
Taguchi L9 orthogonal array experimental layout Experiment Factor A B 1 1 1 2 1 2 3 1 3 4 2 1 5 2 2 6 2 3 7 3 1 8 3 2 9 3 3 Taguchi method signal to noise (S/N) ratio is used to represent the quality characteristic and the largest value of S/N ratio is required.
References [1] J.
Materials Science and Engineering A 532 (2012) 476-479

HIGH ACTIVITY PHOTOCATALYST POWDER FORMED BY THREE CERAMIC OXIDES Perazolli, L.1, Pegler, G.F.1, Silva, M.R.A.2, Ingino R.A.F.1 and Varela J.A.1 1 UNESP –Araraquara Chemical Institute – Rua Prof.
Figure 1.
(a) Structural formula of Rhodamine B, molecular formula: C28H31N2O3Cl, molecular weight: 479,02 g/mol.
References [1] P.R.
Nova, Vol. 26, (2203), n°1, p.133-135

The results were shown in Table 1.
The results were shown in Table 1.
References [1] Yikun Zhang,Baoqing Liu, Jialing Jiang, et al.
Chemical Engineering Journal ,2008 ,137 (3) : 471-479
Development of Researches on Soil Phosphorus[J],Research of Soil and Water Conservation,2003，10(1)：65-67

(a) (b) (c) Fig. 1.
Fig. 1.
Table 1.
References [1] V.A.
Res. 9 (3) (2007) 479– 489

Table 1.
The beams showed the behavior in Fig. 1.
References [1] PlevrisN, Triantafillou TC.
Mater Struct, Springer, 2010;43(1-2):141-50
Eng., ASCE, 2005, 131(1), 173-187.

However the mass of the grapes was reduced at higher rate on day 1 and then reduced and again raised on day 3 but less than day 1.
EC-1, No.4, December 1986 31-33
EC-1, No.4, December 1986 31-33
Mgmt Vol. 27, No. 1, pp. 55-59, 1987
Ashokkumar, Study of a hybrid solar-solar air heater combined with solar cells, Energy Conversion Management, Vol. 31, No. 5 pp 471-479, 1991

The structure of the combustor is shown in the Fig. 1.
Fig.1 Combustor structural model Referred to the burner design manual [11] and cyclone chamber design data [12], the definite size of the combustor (in Fig. 1 and Table 1) has been designed.
When φ=1, L=0, the equation become the continuous equation.
References [1] Bochuan Lin, Enjian Chen.
The Chinese Journal of Process Engineering,2005,5(5):479-484.

Fig. 1.
The material properties that were utilized in the model are listed in Table 1.
Table 1.
References [1] Ch.
Zeszotek, An experimental investigation into the temperature profile of a compliant foil air bearing, Tribology Transactions 47(4) (2004) 470-479

It is a fast and economically viable alternative for manufacturing objects with complex designs [1,2,3].
Fig. 1.
Table 1.
Level 400-200 μm Level 500-300 μm Level 600-400 μm Channel 1 Channel 2 Channel 3 Channel 1 Channel 2 Channel 3 Channel 1 Channel 2 Channel 3 500 474 476 495 479 490 505 517 503 520 495 498 506 500 511 527 539 534 509.9 484.39 486.88 500.47 489.39 500.39 515.88 527.89 518.27 Median=503.11 μm Standard Deviation=18.57 In fig. 12, the device of 400-200 µm was divided into 5 blocks, corresponding to the 2 steps present.
References [1] H.

Table 1.
However, the energy levels and capture cross sections of the Fig 1.
A selection of these are summarized in Table 1 from Refs [6-9].
References [1] T.
Macdonald, Investigating internal gettering of iron at grain boundaries in multicrystalline silicon via photoluminescence imaging, IEEE Journal of Photovoltaics, 2, (2012) 479