Papers by Author: Tetsuya Takami

Abstract: The reliability of CVD gate oxide was investigated by CCS-TDDB measurement and compared with thermally grown gate oxide. Although the QBD of thermal oxide becomes smaller for the larger oxide area, the QBD of CVD oxide is almost independent of the investigated gate oxide area. The QBD at F = 50% of CVD oxide, 3 C/cm2, is two orders of magnitude larger for the area of 1.96×10-3 cm2 at 1 mA/cm2 compared to that of thermal oxide. More than 80% of the CVD oxide breakdown occurs at the field oxide edge and more than 70% of the thermal oxide breakdown in the inner gate area. These results suggest that the lifetime of CVD oxide is hardly influenced by the quality of SiC, while the defects and/or impurities in SiC affect the lifetime of thermally grown oxide.

Abstract: Inversion-type 4H-SiC power MOSFETs using p-body implanted with retrograde profiles have been fabricated. The Al concentration at the p-body surface (Nas) is varied in the range from 5×1015 to 2×1018 cm-3. The MOSFETs show normally-off characteristics. While the Ron is 3 cm2 at Eox = (Vg-Vth)/dox ≅ 3 MV/cm for the MOSFET with the Nas of 2×1018 cm-3, the Ron is reduced by a decrease in the Nas and 26 mcm2 is attained for the device with the Nas of 5×1015 cm-3. The inversion channel mobility and threshold voltage are improved with a decrease in the Nas. By modifying the structural parameter of the MOSFET, a still smaller Ron of 7 mcm2 is achieved with a blocking voltage of 1.3 kV.

Abstract: Prototype SiC power modules are fabricated using our class 10 A, 1.2 kV SiC-MOSFETs and SiC-SBDs, and their switching characteristics are evaluated using a double pulse method. Switching waveforms show that both overshoot and tail current, which induce power losses, are suppressed markedly compared with conventional Si-IGBT modules with similar ratings. The total switching loss (MOSFET turn-ON loss, turn-OFF loss and SBD recovery loss) of SiC power modules is measured to be about 30% of that of Si-IGBT modules under the generally-used switching condition (di/dt ~250A/μs). The three losses of SiC modules decrease monotonically with a decrease in gate resistance, namely switching speed. The result shows the potential of unipolar device SiC power modules.

Abstract: 4H-SiC epilayer channel MOSFETs are fabricated. The MOSFETs have an n- epilayer channel which improves the surface where the MOS channel is formed. By the optimization of the epilayer channel and the MOSFET cell structure, an ON-resistance of 12.9 m
cm2 is obtained at VG = 12 V (Eox = 2.9 MV/cm). A normally-OFF operation and stable avalanche breakdown is obtained at the drain voltage larger than 1.2 kV. Both the ON-resistance and the breakdown voltage increase slightly with an increase in temperature. This behavior is favorable for high power operation. By the evaluation of the control MOSFETs with n+ implanted channel, the resistivity of the MOS channel is estimated. The MOS channel resistivity is proportional to the channel length and it corresponds to an effective channel mobility of about 20 cm2/Vs.

Abstract: The effect of N2O anneal on channel mobility of inversion-type 4H-SiC n-channel MOSFET has been systematically investigated. It is found that the mobility increases with increasing anneal temperature from 900 to 1150°C. The highest field effect mobility of 30 cm2/Vs is achieved by 1150°C anneal for 3 h, which is about 20 times higher than that for non-annealed MOSFET. In order to investigate the oxide reliability, TDDB measurement has been performed on SiO2 grown on n-type 4H-SiC. The oxide lifetime is found to be drastically improved by N2O anneal.